manualshive.com logo in svg

Texas Instruments DS90UB954-Q1EVM, User Manual, Page: 36 / 67

Share
Download
Texas Instruments DS90UB954-Q1EVM User Manual Download Page 36

Figure 14-3. ALP in Demo Mode

Disable the demo mode by selecting the “Preferences” pull down menu and un-checking “Enable Demo Mode”.

Figure 14-4. ALP Preferences Menu

After demo mode is disabled, the ALP software will poll the ALP hardware. The ALP software will update and 
have only “DS90UB954” under the “Devices” pull down menu.

14.2 USB2ANY Firmware Issues

If upon plugging in the board to the PC, the user is presented with a message stating USB2ANY firmware is 
out of date or is 0.0.0.0, similar to 

Figure 14-5

, try unplugging the USB cable and plugging it in again (holding 

S1 while plugging in the USB cable puts the USB2ANY into firmware update mode). If that does not solve 
the problem you will have to re-flash the on-board USB2ANY firmware. To re-flash the USB2ANY, download 

USB2ANY Explorer

 and install the application. Launch the USB2ANY Firmware Loader available at "C:\Program 

Files (x86)\TI USB2ANY SDK\bin\USB2ANY Firmware Loader.exe" and follow the instructions to flash the latest 
version of USB2ANY firmware. The firmware loading screen is shown in 

Figure 14-6

.

Troubleshooting ALP Software

www.ti.com

36

DS90UB954-Q1EVM Deserializer User's Guide

SNLU223C – AUGUST 2017 – REVISED NOVEMBER 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

Summary of Contents for DS90UB954-Q1EVM




































































Reviews:

No comments