Texas Instruments DLP5532HBQ1EVM User Manual Download Page 1 | Manualshive

Page: 1 / 21

Texas Instruments DLP5532HBQ1EVM User Manual Download Page 1

User’s Guide

DLP5532HBQ1EVM Evaluation Module

ABSTRACT

The DLP5532HBQ1EVM Evaluation Module (EVM) is a complete electronic subsystem designed to control
the DLP5532-Q1 chipset. The DLP5532-Q1 chipset consists of the DLP5532-Q1, the DLPC230-Q1, and the
TPS99000-Q1. When combined with illumination and projection optics, RGB LEDs and a photodiode, this EVM
can be used to develop an automotive grade high brightness projector for applications such as augmented
reality head-up display (AR HUD) or other window display. This electronics EVM includes an LED illumination
driver board, which is capable of independently driving up to 10 A and 17 V per each of the three color channels.

Except for the DMD, there are no optical elements provided with this EVM. It is expected that this EVM is
procured to mount to a custom designed picture generation unit (PGU) or projector.

The DLP5532HBQ1EVM is not a production design. It is intended for evaluation only.

Figure 1-1. The DLP5532HBQ1EVM

DLPU108 – MAY 2022

Submit Document Feedback

DLP5532HBQ1EVM Evaluation Module

1

Copyright © 2022 Texas Instruments Incorporated

1
2
3
...
»

Summary of Contents for DLP5532HBQ1EVM






















Reviews:

No comments