Texas Instruments DAC 3202 Series Manual Download Page 3 | Manualshive

Page: 3 / 83

background image

5 Pin Configuration and Functions

16

VREF

5

GPIO/SDO

1

FB0

12

FB1

15

VDD

6

SCL/

SYNC

2

OUT0

11

OUT1

14

AGND

7

A0/SDI

3

NC

10

NC

13

CAP

8

SDA/SCLK

4

NC

9

NC

Not to scale

Thermal Pad

Figure 5-1. RTE (16-pin WQFN) Package, Top View

Table 5-1. Pin Functions

PIN

TYPE

DESCRIPTION

NO.

NAME

1

FB0

Input

Voltage feedback pin for channel 0.
In voltage-output mode, connect to OUT0 for closed-loop amplifier output.
In current-output mode, keep the FB0 pin unconnected to minimize leakage current.

2

OUT0

Output

Analog output voltage from DAC channel 0.

3

NC

NC

No connection. Leave the pin unconnected.

4

NC

NC

No connection. Leave the pin unconnected.

5

GPIO/SDO

Input/Output

General-purpose input/output configurable as LDAC, PD, PROTECT, RESET, SDO, and STATUS.
For STATUS and SDO, connect the pin to the IO voltage with an external pullup resistor.
If unused, connect the GPIO pin to VDD or AGND using an external resistor. This pin can ramp up before VDD.

6

SCL/SYNC

Output

I

2

C serial interface clock or SPI chip select input. This pin must be connected to the IO voltage using an external

pullup resistor. This pin can ramp up before VDD.

7

A0/SDI

Input

Address configuration pin for I

2

C or serial data input for SPI.

For A0, connect this pin to VDD, AGND, SDA, or SCL for address configuration (

Section 7.5.2.2.1

For SDI, this pin does not need to be pulled up or pulled down. This pin can ramp up before VDD.

8

SDA/SCLK

Input/Output

Bidirectional I

2

C serial data bus or SPI clock input. This pin must be connected to the IO voltage using an external

pullup resistor in I

2

C mode. This pin can ramp up before VDD.

9

NC

NC

No connection. Leave the pin unconnected.

10

NC

NC

No connection. Leave the pin unconnected.

11

OUT1

Output

Analog output voltage from DAC channel 1.

12

FB1

Input

Voltage feedback pin for channel 1.
In voltage-output mode, connect to OUT1 for closed-loop amplifier output.
In current-output mode, keep the FB1 pin unconnected to minimize leakage current.

13

CAP

Power

External bypass capacitor for the internal LDO. Connect a capacitor (approximately 1.5 μF) between CAP and AGND.

14

AGND

Ground

Ground reference point for all circuitry on the device.

15

VDD

Power

Supply voltage.

16

VREF

Power

External reference input. Connect a capacitor (approximately 0.1 μF) between VREF and AGND.
Use a pullup resistor to VDD when the external reference is not used. This pin must not ramp up before VDD. In case
an external reference is used, make sure the reference ramps up after VDD.

Thermal
pad

Thermal Pad

Ground

Connect the thermal pad to AGND.

DAC53202, DAC63202

SLASF47 – MAY 2022

Copyright © 2022 Texas Instruments Incorporated

Submit Document Feedback

3

Product Folder Links:

«
1
2
3
4
5
...
»

Summary of Contents for DAC 3202 Series




















































































Reviews:

No comments

Related manuals for DAC 3202 Series

Brand: EAS Electric Pages: 4

Brand: EAS Electric Pages: 31

Brand: Qcells Pages: 80

Brand: Q CELLS Pages: 32

EAL580 MT Series

Brand: Baumer Pages: 74

UNIRAC POLETOPS 5000 Series

Brand: Hilti Pages: 4

AIS Splitter 100

Brand: Raymarine Pages: 24

Brand: E-matic Pages: 22

Brand: Agilent Technologies Pages: 122

Brand: Promate Pages: 28

Brand: Zlpower Pages: 24

EdgeVis HD-IP200

Brand: Digital Barriers Pages: 34

COM-K IMR01Z01-E9

Brand: RKC INSTRUMENT Pages: 2

Brand: Kramer Pages: 2

VideoExpress Converter

Brand: Miglia Pages: 12

Mark Levinson 5101

Brand: Harman Pages: 19

Brand: GarrettCom Pages: 60

Brand: MediaKind Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands