manualshive.com logo in svg

Texas Instruments CC2533, User Manual

Share
Download
Texas Instruments CC2533 User Manual Download Page 140

ADC Operation

www.ti.com

The

ADCCON3

register controls the channel number, reference voltage, and decimation rate for a single

conversion. The single conversion takes place immediately after the

ADCCON3

register is written to, or if a

conversion sequence is ongoing, immediately after the sequence has ended. The coding of the register
bits is exactly as for

ADCCON2

.

12.2.5 ADC Conversion Results

The digital conversion result is represented in 2s-complement form. For single-ended configurations, the
result can be expected to be positive. This is because the result is the difference between the input signal
and ground, which is always positively signed (Vconv = Vinp

–

Vinn, where Vinn = 0 V). The maximum

value is reached when the input signal is equal to VREF, the selected voltage reference. For differential
configurations, the difference between two pins is converted, and this difference can be negatively signed.
For example, with a decimation rate of 512 using only the 12 MSBs of the digital conversion result
register, the maximum value of 2047 is reached when the analog input (Vconv) is equal to VREF, and
minimum value of

–

2048 is reached when the analog input is equal to

–

VREF .

The digital conversion result is available in

ADCH

and

ADCL

when

ADCCON1.EOC

is set to 1. Note that the

conversion result always resides in the MSB section of the combined

ADCH

and

ADCL

registers.

When the

ADCCON2.SCH

bits are read, they indicate the channel on which conversion is ongoing. The

results in

ADCL

and

ADCH

normally apply to the previous conversion. If the conversion sequence has

ended,

ADCCON2.SCH

has a value of one more than the last channel number, but if the channel number

last written to

ADCCON2.SCH

was 12 or more, the same value is read back.

12.2.6 ADC Reference Voltage

The positive reference voltage for analog-to-digital conversions is selectable as either an internally
generated voltage, the AVDD5 pin, an external voltage applied to the AIN7 input pin, or a differential
voltage applied to the AIN6

–

AIN7 inputs.

The accuracy of the conversion results depend on the stability and noise properties of the reference
voltage. Offset from the wanted voltage introduces a gain error in the ADC proportional to the ratio of the
wanted voltage and the actual voltage. Noise on the reference must be lower than quantization noise of
the ADC to ensure the specified SNR is achieved.

12.2.7 ADC Conversion Timing

The ADC should only be used with the 32-MHz XOSC, and no system clock division should be
implemented by the user. The actual ADC sampling frequency of 4 MHz is generated by fixed internal
division. The time required to perform a conversion depends on the selected decimation rate. In general,
the conversion time is given by:

Tconv = (decimation rate + 16)

×

0.25

μ

s.

12.2.8 ADC Interrupts

The ADC generates an interrupt when a single conversion triggered by writing to

ADCCON3

has completed.

No interrupt is generated when a conversion from the sequence is completed.

12.2.9 ADC DMA Triggers

The ADC generates a DMA trigger every time a conversion from the sequence has completed. When a
single conversion completes, no DMA trigger is generated.

There is one DMA trigger for each of the eight channels defined by the first eight possible settings for

ADCCON2.SCH

. The DMA trigger is active when a new sample is ready from the conversion for the

channel. The DMA triggers are named ADC_CHsd in

Table 8-1

, where s is single-ended channel and d is

differential channel.

In addition, one DMA trigger, ADC_CHALL, is active when new data is ready from any of the channels in
the ADC conversion sequence.

140

ADC

SWRU191C

–

April 2009

–

Revised January 2012

Submit Documentation Feedback

Copyright

©

2009

–

2012, Texas Instruments Incorporated

Summary of Contents for CC2533



















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands