manualshive.com logo in svg

Texas Instruments CC2533, User Manual

Share
Download
Texas Instruments CC2533 User Manual Download Page 139

www.ti.com

ADC Operation

The single-ended inputs AIN0 through AIN7 are represented by channel numbers 0 to 7. Channel
numbers 8 through 11 represent the differential inputs consisting of AIN0

–

AIN1, AIN2

–

AIN3, AIN4

–

AIN5,

and AIN6

–

AIN7. Channel numbers 12 through 15 represent GND (12), temperature sensor (14), and

AVDD5/3 (15), with channel 13 being reserved. These values are used in the

ADCCON2.SCH

and

ADCCON3.SCH

fields.

The ADC input is a switched capacitance stage which draws current during the conversion. As an
example, the equivalent input impedance of a typical device was found to be 176 k

Ω

when used with an

input voltage of 3 V, a 512

×

decimation rate, and the internal reference.

12.2.2 ADC Conversion Sequences

The ADC can perform a sequence of conversions and move the results to memory (through DMA) without
any interaction from the CPU.

The conversion sequence can be influenced with the

APCFG

register (see

Section 7.6.6

), in that the eight

analog inputs to the ADC come from I/O pins that are not necessarily programmed to be analog inputs. If
a channel should normally be part of a sequence, but the corresponding analog input is disabled in the
APCFG register, then that channel is skipped. When using differential inputs, both pins in a differential pair
must set as analog input pins in the

APCFG

register.

The

ADCCON2.SCH

register bits are used to define an ADC conversion sequence from the ADC inputs. If

ADCCON2.SCH

is set to a value less than 8, the conversion sequence contains a conversion from each

channel from 0 up to and including the channel number programmed in

ADCCON2.SCH

. When

ADCCON2.SCH

is set to a value between 8 and 12, the sequence consists of differential inputs, starting at

channel 8 and ending at the programmed channel. For

ADCCON2.SCH

greater than or equal to 12, the

sequence consists of the selected channel only.

12.2.3 Single ADC Conversion

In addition to this sequence of conversions, the ADC can be programmed to perform a single conversion
from any channel. Such a conversion is triggered by writing to the

ADCCON3

register. The conversion

starts immediately unless a conversion sequence is already ongoing, in which case the single conversion
is performed as soon as that sequence is finished.

12.2.4 ADC Operating Modes

This section describes the operating modes and initialization of conversions.

The ADC has three control registers:

ADCCON1

,

ADCCON2

, and

ADCCON3

. These registers are used to

configure the ADC and to report status.

The

ADCCON1.EOC

bit is a status bit that is set high when a conversion ends and cleared when ADCH is

read.

The

ADCCON1.ST

bit is used to start a sequence of conversions. A sequence starts when this bit is set

high,

ADCCON1.STSEL

is 11, and no conversion is currently running. When the sequence is completed,

this bit is automatically cleared.

The

ADCCON1.STSEL

bits select the event that starts a new sequence of conversions. The options which

can be selected are rising edge on external pin P2.0, end of previous sequence, a Timer 1 channel 0
compare event, or

ADCCON1.ST

is 1.

The

ADCCON2

register controls how the sequence of conversions is performed.

ADCCON2.SREF

is used to select the reference voltage. The reference voltage should only be changed

when no conversion is running.

The

ADCCON2.SDIV

bits select the decimation rate, thereby also the resolution and time required to

complete a conversion, and hence the sample rate. The decimation rate should only be changed when no
conversion is running.

The last channel of a sequence is selected with the

ADCCON2.SCH

bits as described previoiusly.

139

SWRU191C

–

April 2009

–

Revised January 2012

ADC

Submit Documentation Feedback

Copyright

©

2009

–

2012, Texas Instruments Incorporated

Summary of Contents for CC2533



















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands