Texas Instruments CC2500 Manual Download

Page: 81 / 96

CC2500

SWRS040C

Page 81 of 89

0x2B: AGCTEST – AGC Test

Bit

Field Name

Reset

R/W

Description

7:0

AGCTEST[7:0]

63
(0x3F)

R/W

For test only. Do not write to this register.

0x2C: TEST2 – Various Test Settings

Bit

Field Name

Reset

R/W

Description

7:0

TEST2[7:0]

136 (0x88)

R/W

Set to 0x81 for improved sensitivity at data rates

≤

100 kBaud. The

temperature range is then from 0

C to +85

0x2D: TEST1 – Various Test Settings

Bit

Field Name

Reset

R/W

Description

7:0

TEST1[7:0]

49 (0x31)

R/W

Set to 0x35 for improved sensitivity at data rates

≤

100 kBaud. The

temperature range is then from 0

C to +85

0x2E: TEST0 – Various Test Settings

Bit

Field Name

Reset

R/W

Description

7:2

TEST0[7:2]

2 (0x02)

R/W

The value to use in this register is given by the SmartRF



Studio

software [5].

VCO_SEL_CAL_EN

R/W

Enable VCO selection calibration stage when 1

TEST0[0]

R/W

The value to use in this register is given by the SmartRF



Studio

software [5].

32.3

Status Register Details

0x30 (0xF0): PARTNUM – Chip ID

Bit

Field Name

Reset

R/W

Description

7:0

PARTNUM[7:0]

128 (0x80)

Chip part number

0x31 (0xF1): VERSION – Chip ID

Bit

Field Name

Reset

R/W

Description

7:0

VERSION[7:0]

3 (0x03)

Chip version number.

0x32 (0xF2): FREQEST – Frequency Offset Estimate from Demodulator

Bit

Field Name

Reset

R/W

Description

7:0

FREQOFF_EST

The estimated frequency offset (2’s complement) of the carrier.
Resolution is F

XTAL

(1.59 - 1.65 kHz); range is ±202 kHz to

±210 kHz, dependent of XTAL frequency.

Frequency offset compensation is only supported for 2-FSK;
GFSK and MSK modulation. This register will read 0 when
using OOK modulation.

Summary of Contents for CC2500

































































































Search results

Summary of Contents for CC2500

Reviews:

Related manuals for CC2500

Brands by name

Popular brands

Texas Instruments CC2500, Manual

Search results

Summary of Contents for CC2500

Reviews:

Related manuals for CC2500

Brands by name

Popular brands