manualshive.com logo in svg

Texas Instruments bq34z100EVM, User Manual, Page: 3 / 28

Share
Download
Texas Instruments bq34z100EVM User Manual Download Page 3

1 Features

• Complete evaluation system for the bq34z100 advanced gas gauge with Impedance Track

™

 technology.

• Populated circuit module for quick setup
• Link to software allowing data logging for system analysis

1.1 Kit Contents

• bq34z100 circuit module
• Cable to connect the EVM to an EV2300 or EV2400 Communications Interface Adapter.

1.2 Ordering Information

Table 1-1. Ordering Information

EVM Part Number

Chemistry

Configuration

Capacity

bq34z100EVM

Li-Ion, Li-Polymer, LiFePO4, PbA,

NiMH, NiCd

3 V–48 V

Any

1.3 Documentation

See the device data sheet for bq34z100-G1 (

SLUSBZ5

) on 

www.ti.com

 for information on device firmware and

hardware.

1.4 bq34z100 Circuit Module Performance Specification Summary

This section summarizes the performance specifications of the bq34z100 circuit module.

Specification

Min

Typ

Max

Unit

Input voltage BAT+ to BAT– in 1S mode

3

4

5

V

Input voltage BAT+ to BAT– in MultiCell

6

28

48

V

Charge and discharge current

0

2

7

A

www.ti.com

Features

SLUU904B – APRIL 2012 – REVISED APRIL 2021

Submit Document Feedback

bq34z100EVM Wide Range Impedance Track™ Enabled Battery Fuel Gauge

Solution

3

Copyright © 2021 Texas Instruments Incorporated

Summary of Contents for bq34z100EVM





























Reviews:

No comments