Texas Instruments BOOST-PSEMTHR8-097 User Manual Download Page 10 | Manualshive

Page: 10 / 34

Texas Instruments BOOST-PSEMTHR8-097 User Manual Download Page 10

TPS23882 GUI Setup

10

SLVUBQ3 – August 2019

Submit Documentation Feedback

Copyright © 2019, Texas Instruments Incorporated

TPS23882EVM: PoE, PSE, TPS23882 Evaluation Module

Figure 4. TPS23882 GUI Startup Window

The default device address in the GUI is set to 0x20 which matches the default configuration of the EVM
(J4 on the daughter card is installed with jumpers). The GUI sets the TPS23882 in configuration B mode
(see the

GENERAL MASK Register

section of the data sheet for details). The address can be programed

through the A1 to A4 pins and the I2C address setting in the GUI needs to match the hardware
configuration. See the

Pin Status Register

section of the data sheet for details. The startup page contains

links to the EVM user's guide, TPS23882 data sheet, E2E forum and MSP430 reference code. Four
popular PD end-equipment images are connected to the PSE switch. Links to the recommended PD
device for each end equipment are also provided.

Once the TPS23882 device is connected, click Firmware to select firmware to be loaded to TPS23882.

«
...
8
9
10
11
12
...
»

Summary of Contents for BOOST-PSEMTHR8-097



































Reviews:

No comments