manualshive.com logo in svg

Texas Instruments AM335 Series, Technical Reference Manual

The Texas Instruments AM335 Series is a high-performance microprocessor family. To conveniently get started with this versatile product, you can access the free Quick Start Manual on our website. Download this comprehensive manual to explore the product's features, functions, and begin your journey with the AM335 Series.

Share
Download
background image

www.ti.com

Functional Description

To reset the autobauding hardware (to start a new AT detection) or to set the UART in standard mode (no
autobaud), the UARTi.UART_MDR1[2:0] MODE_ SELECT bit field must be set to reset state (0x7) and
then to the UART in autobauding mode (0x2) or to the UART in standard mode (0x0).

Use limitation:

•

Only 7- and 8-bit characters (5- and 6-bit not supported)

•

7-bit character with space parity not supported

•

Baud rate between 1200 and 115,200 bps (10 possibilities)

19.3.8.1.3.5 Error Detection

When the UARTi.UART_LSR register is read, the UARTi.UART_LSR[4:2] bit field reflects the error bits
(BI: break condition, FE: framing error, PE: parity error) of the character at the top of the RX FIFO (the
next character to be read). Therefore, reading the UARTi.UART_LSR register and then reading the
UARTi.UART_RHR register identifies errors in a character.

Reading the UARTi.UART_RHR register updates the BI, FE, and PE bits (see

Table 19-11

for the UART

mode interrupts).

The UARTi.UART_LSR[7] RX_FIFO_STS bit is set when there is an error in the RX FIFO and is cleared
only when no errors remain in the RX FIFO.

NOTE:

Reading the UARTi.UART_LSR register does not cause an increment of the RX FIFO read

pointer. The RX FIFO read pointer is incremented by reading the UARTi.UART_RHR
register.

Reading the UARTi.UART_LSR register clears the OE bit if it is set (see

Table 19-11

for the UART mode

interrupts).

19.3.8.1.3.6 Overrun During Receive

Overrun during receive occurs if the RX state-machine tries to write data into the RX FIFO when it is
already full. When overrun occurs, the device interrupts the MPU with the UARTi.UART_IIR[5:1] IT_TYPE
bit field set to 0x3 (receiver line status error) and discards the remaining portion of the frame.

Overrun also causes an internal flag to be set, which disables further reception. Before the next frame can
be received, the MPU must:

•

Reset the RX FIFO.

•

Read the UARTi.UART_RESUME register, which clears the internal flag.

19.3.8.1.3.7 Time-Out and Break Conditions

19.3.8.1.3.7.1 Time-Out Counter

An RX idle condition is detected when the receiver line (uarti_rx) is high for a time that equals 4x the
programmed word  12 bits. uarti_rx is sampled midway through each bit.

For sleep mode, the counter is reset when there is activity on uarti_rx.

For the time-out interrupt, the counter counts only when there is data in the RX FIFO, and the count is
reset when there is activity on uarti_rx or when the UARTi.UART_RHR register is read.

19.3.8.1.3.7.2 Break Condition

When a break condition occurs, uarti_tx is pulled low. A break condition is activated by setting the
UARTi.UART_LCR[6] BREAK_EN bit. The break condition is not aligned on word stream (a break
condition can occur in the middle of a character). The only way to send a break condition on a full
character is:

1. Reset the TX FIFO (if enabled).

2. Wait for the transmit shift register to empty (the UARTi.UART_LSR[6] TX_SR_E bit is set to 1).

3479

SPRUH73H – October 2011 – Revised April 2013

Universal Asynchronous Receiver/Transmitter (UART)

Submit Documentation Feedback

Copyright © 2011–2013, Texas Instruments Incorporated

Summary of Contents for AM335 Series


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AM335 Series

Panasonic WJ-NV200K Quick Reference Manual preview
WJ-NV200K
Brand: Panasonic Pages: 4
dbx ProVocal Specifications preview
ProVocal
Brand: dbx Pages: 2
H3C S5120V3-EI Series Manual preview
S5120V3-EI Series
Brand: H3C Pages: 54
Ublox LENA-R8 Series System Integration Manual preview
LENA-R8 Series
Brand: Ublox Pages: 116
Q-See QC814 Specifications preview
QC814
Brand: Q-See Pages: 2
Moxa Technologies UC-8100 Series Hardware User Manual preview
UC-8100 Series
Brand: Moxa Technologies Pages: 19
Lancom 7100 VPN Manual preview
7100 VPN
Brand: Lancom Pages: 70
Lanner ICS-P570 User Manual preview
ICS-P570
Brand: Lanner Pages: 63
AXIOMTEK AIE900-XNX Series User Manual preview
AIE900-XNX Series
Brand: AXIOMTEK Pages: 53
SIIG ID-P20211-S1 Quick Installation Manual preview
ID-P20211-S1
Brand: SIIG Pages: 20
Moxa Technologies TAP-125 Series User Manual preview
TAP-125 Series
Brand: Moxa Technologies Pages: 51
Omron ACCURAX G5 - Quick Start Manual preview
ACCURAX G5 -
Brand: Omron Pages: 13
ZALMAN ZM-2HC2 User Manual preview
ZM-2HC2
Brand: ZALMAN Pages: 8
Intel E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor Datasheet preview
E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor
Brand: Intel Pages: 112
SmartBridges airPoint Nexus sB3210 User Manual preview
airPoint Nexus sB3210
Brand: SmartBridges Pages: 55
Westermo Viper-012 User Manual preview
Viper-012
Brand: Westermo Pages: 22
IBM 55PUS8118 SCSI-2 Installation Manual preview
55PUS8118 SCSI-2
Brand: IBM Pages: 42
EZCast M2 User Manual preview
M2
Brand: EZCast Pages: 27

Brands by name

Popular brands

Load more brands