Texas Instruments AM1808 Technical Reference Manual Download Page 315 | Manualshive

Page: 315 / 1820

background image

Overview

315

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

Programmable Real-Time Unit Subsystem (PRUSS)

The Programmable Real-Time Unit Subsystem (PRUSS) consists of:

•

Two programmable real-time units (PRU0 and PRU1) and their associated memories.

•

An interrupt controller (INTC) for handling system interrupt events. The INTC also supports posting
events back to the device level host CPU.

•

A Switched Central Resource (SCR) for connecting the various internal and external masters to the
resources inside the PRUSS.

The two PRUs can operate completely independently or in coordination with each other. The two PRUs
can also work in coordination with the device level host CPU. This is determined by the nature of the
program that is loaded into the two PRUs instruction memory. Several different signaling mechanisms are
available between the two PRUs and the device level host CPU.

The two PRUs are optimized for performing embedded tasks that require manipulation of packed memory-
mapped data structures, handling of system events that have tight real-time constraints and interfacing
with systems external to the device.

13.1 Overview

The PRU is a optimized for performing embedded tasks that require manipulation of packed memory
mapped data structures, handling of system events that have tight realtime constraints and interfacing with
systems external to the DSP/SoC. The PRU is both very small and very efficient at handling such tasks.

The major attributes of the PRU are as follows:

Attribute

Value

IO Architecture

Load / Store

Data Flow Architecture

Register to Register

Core Level Bus Architecture

Type

4-Bus Harvard (1 Instruction, 3 Data)

Instruction I/F

32-Bit

Memory I/F 0

32-Bit

Memory I/F 1

32-Bit

Execution Model

Issue Type

Scalar

Pipelining

None

Ordering

In-order

ALU Type

Unsigned Integer

Registers

General Purpose (GP)

30 (R1 – R30)

External Status

1 (R31)

GP / Indexing

1 (R0)

Addressability

Bit, Byte (8-bit), Halfword (16-bit), Word (32-bit), Pointer

«
...
313
314
315
316
317
...
»

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AM1808

Brand: IBM Pages: 86

Brand: IBM Pages: 104

System Storage TS3100

Brand: IBM Pages: 375

Device Server UDS 10

Brand: Lantronix Pages: 8

Brand: Lattice Semiconductor Pages: 15

iCE40 UltraLite

Brand: Lattice Semiconductor Pages: 13

Brand: Amperes Pages: 8

Magic WiFi mini Ek

Brand: Devolo Pages: 22

Brand: XMOS Pages: 6

Brand: Z3 Technology Pages: 67

Brand: MFJ Pages: 11

CNPS5X PERFORMA

Brand: ZALMAN Pages: 8

Brand: Symantec Pages: 100

Brand: Ista Pages: 16

Brand: B&B Electronics Pages: 24

Brand: Homeworks Pages: 24

Brand: LevelOne Pages: 2

Brand: Matrix Switch Corporation Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands