Texas Instruments AM1808 Technical Reference Manual Download Page 247

Page: 247 / 1820

www.ti.com

SYSCFG Registers

247

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

System Configuration (SYSCFG) Module

10.5.10.14 Pin Multiplexing Control 13 Register (PINMUX13)

Figure 10-31. Pin Multiplexing Control 13 Register (PINMUX13)

PINMUX13_31_28

PINMUX13_27_24

PINMUX13_23_20

PINMUX13_19_16

R/W-0

PINMUX13_15_12

PINMUX13_11_8

PINMUX13_7_4

PINMUX13_3_0

R/W-0

LEGEND: R/W = Read/Write; -

= value after reset

(1)

I = Input, O = Output, I/O = Bidirectional, X = Undefined, Z = High-impedance state

Table 10-35. Pin Multiplexing Control 13 Register (PINMUX13) Field Descriptions

Bit

Field

Value

Description

Type

(1)

31-28

PINMUX13_31_28

PRU0_R30[26]/ UHPI_HRW/UPP_CHA_WAIT/GP6[8]/PRU1_R31[17] Control

Selects Function PRU1_R31[17]

Selects Function PRU0_R30[26]

Selects Function UHPI_HRW

Reserved

Selects Function UPP_CHA_WAIT

I/O

5h-7h

Reserved

Selects Function GP6[8]

I/O

9h-Fh

Reserved

27-24

PINMUX13_27_24

PRU0_R30[27]/UHPI_HHWIL/UPP_CHA_ENABLE/GP6[9] Control

Pin is 3-stated.

Selects Function PRU0_R30[27]

Selects Function UHPI_HHWIL

Reserved

Selects Function UPP_CHA_ENABLE

I/O

5h-7h

Reserved

Selects Function GP6[9]

I/O

9h-Fh

Reserved

23-20

PINMUX13_23_20

PRU0_R30[28]/UHPI_HCNTL1/UPP_CHA_START/GP6[10] Control

Pin is 3-stated.

Selects Function PRU0_R30[28]

Selects Function UHPI_HCNTL1

Reserved

Selects Function UPP_CHA_START

I/O

5h-7h

Reserved

Selects Function GP6[10]

I/O

9h-Fh

Reserved

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for AM1808

Reviews:

Texas Instruments AM1808, Technical Reference Manual, Page: 247 / 1820

Search results

Summary of Contents for AM1808

Reviews: