background image

4.3

Inverted Interrupts

Parallel EVM Site

www.ti.com

The interface card provides four options for a clock source to the parallel EVM interface with use of a
2-mm shunt on J14.

Table 8. Parallel EVM Clocking Options via J14

Shunt on Pins

Clock Source

1–2

DC_TOUTa

3–4

DC_TOUTa

5–6

DC_CLKXa

7–8

DC_CLKXb

The interface card provides two options for an external interrupt source to the DSP with use of a 2-mm
shunt on J15.

Table 9. External Interrupt Source via J13

(1)

Shunt on Pins

Connects To:

Rev A PWB

Rev B PWB

1–2

DC_INTa

DC_INTb

3–4

DC_INTb

DC_INTb

5–6

DC_INTc

DC_INTd

7–8

DC_INTd

DC_INTd

(1)

External interrupts shown in this table are based on the TMS320C6711 DSK.

Jumper W7 on the 5–6K Interface Board revision B expands the interrupt capabilities of certain
data-converter EVMs. W7 controls the signal applied to J13 via single-gate inverter U7. When a shunt is
installed on W7-pins 1-2 (default), the interrupt signal is applied directly to J13. Installing the shunt on
W7-pins 2-3 provides an interrupt inverted signal to J13 via U7.

List of Tables

6

SLAU104C – May 2004 – Revised March 2009

Submit Documentation Feedback

Summary of Contents for 5-6K
















Reviews: