manualshive.com logo in svg

Tews Technologies TMVE8240-11, User Manual

Share
Download
Tews Technologies TMVE8240-11 User Manual Download Page 39

 

 

TVME8240 User Manual Issue 1.2.9 

Page 39 of 70 

 

EEPROM 

Address 

0x00 

0x02 

0x04 

0x06 

0x08 

0x0A 

0x0C 

0x0E 

0x00 

0x1498 0x2030 0x0000 0x0000 0x0000 0x0000 0x0000  0x0000 

0x10 

IDCRC 

0x0104 0x0100 0xuv06  0xyzwx 0x2000 0x0000  0x0000 

0x20 

0x0800 0x8602 0x0102 0x0801 0x0001 0x0393 0x0000  0x0103 

0x30 

0x0008 0x0100 0x0000 0xE078 0x0001 0x0050 0x0018  0x0000 

0x40 

0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000  0x0000 

0x50 

0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000  0x0000 

0x60 

0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000  0x0000 

0x70 

0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 

ROMCRC 

ICCRC: 0x00_ID-Block-CRC, ROMCRC: SROM CRC, MAC Addr.: 00_01_06_uv_wx_yz 

Table 7-3 : 21143 Configuration EEPROM Content 

7.3 21143 Ports 

The 21143 MII port connects to an Intel LXT970 Fast Ethernet transceiver to build the Fast Ethernet 
interface available at the RJ45 connector on the front plate. 

The 21143 AUI port connects to the VME P2 connector. 

The 21143 10Base-T TP port is not used. 

7.4 21143 GEP Pin Usage 

The 21143 GEP[0] pin is used as an output that connects to the LXT970 Fast Ethernet transceiver 
reset input. 

A low on the GEP[0] output holds the LXT970 in reset. The LXT970 is also reset by a PCI reset. 

The 21143 GEP[3:1] pins are used as inputs. 

Interrupts for GEP[1:0] inputs must be disabled. 

7.5 Media Capabilities 

10/100Base-TX Ethernet interface on the RJ45 front panel connector.  

AUI port for a 10Base-T or 10Base2 Ethernet interface on the VME P2 Connector. 

 

 

 

Summary of Contents for TMVE8240-11







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands