manualshive.com logo in svg

Tews Technologies TAMC900, User Manual, Page: 41 / 71

Share
Download
Tews Technologies TAMC900 User Manual Download Page 41

 

 

TAMC900 User Manual Issue 2.0.1 

Page 41 of 71 

8  FPGA 

The TAMC900 provides a Virtex-5 FPGA in FFG665 for customer programming and board control. 

Information about the FPGA pin assignment is part of the engineering documentation. 

8.1 Configuration 

The FPGA is configured from a Xilinx Platform Flash. The flash has the potential to store different FPGA 
code revisions. 

The Module Management Controller (MMC) can be programmed to select the code revision that is loaded 
into the FPGA. By default, Code Revision 0 is loaded into the FPGA. 

 

On the TAMC900, the Xilinx Platform Flash is configured to store multiple code revisions. 
The FPGA is configuration Master and loads Revision 0 by default. 
Pay attention to this while generating PROM files. 

 

The Platform Flash or the FPGA are programmed using the Payload JTAG interface. The Payload JTAG 
interface is accessible via the “Payload JTAG connector” (J4). 

 

The on board CPLD is part of the “Payload JTAG Cain”. TEWS recommends setting the CPLD 
in Bypass Mode during FPGA or Platform Flash JTAG operations. 

 

8.2 MMC Interface 

The FPGA has the following signals which are connected to the MMC: 

Interface 

Description 

FUNC_LED2 

This signal can be used to flash the USER LED in the front panel of the TAMC900. 
A rising or falling edge of FUNC_LED2 triggers the MMC to turn the USER LED off for 
app. 100ms. 

EKEY[4:1] 

These signals can be used to transmit connectivity data from the MMC to the FPGA. 
The implementation in MMC and FPGA has to be done by the customer. Please refer to 
the chapter “Module Management Controller (MMC)” for more information. 

I2C 

This I2C Interface can be used by the FPGA to read connectivity data from the MMC. 
The implementation in MMC and FPGA has to be done by the customer. Please refer to 
chapter “Module Management Controller (MMC)” for more information. 

RXD0 / TXD0 

These signals can be used to implement a serial communication between FPGA and 
MMC. 
By default, this is used as debug-output of the MMC. Any other implementation in MMC 
and FPGA has to be done by the customer. 

Table 8-1 :  FPGA Signals connected to the MMC 

Summary of Contents for TAMC900








































































Reviews:

No comments