manualshive.com logo in svg

Tews Technologies TAMC900, User Manual, Page: 30 / 71

Share
Download
Tews Technologies TAMC900 User Manual Download Page 30

 

 

TAMC900 User Manual Issue 2.0.1 

Page 30 of 71 

6.3 Global Channel Configuration 

This register controls global (high-level) operation settings. This includes top-level activation, deactivation 
and trigger activation of certain channels.  

The trigger activation bits have been implemented due to safety consideration. This prevents spurious 
interrupt-processing while requiring arming a channel before using. 

Bit 

Symbol 

Description 

Access 

Reset 
Value 

15 CATE7 

14 CATE6 

13 CATE5 

12 CATE4 

11 CATE3 

10 CATE2 

9 CATE1 

8 CATE0 

To activation a channel for processing a subsequent trigger 
event the corresponding bit has to be set. The bit is reset 
after an event has processed. 

0 = channel 

not

 armed 

1 = channel armed 

R/W 0 

7 CHEN7 

6 CHEN6 

5 CHEN5 

4 CHEN4 

3 CHEN3 

2 CHEN2 

1 CHEN1 

0 CHEN0 

A channel is enabled (CHENx) for internal processing if the 
accompany bit is set. The configuration is done in the way 
0 = disable channel 
1 = enable channel 
 
The channel numbers 0-7 matches the ADC numbers 0-7. 

R/W 0 

Table 6-3 :  Global Channel Configuration Register (Address 0xC) 

 

The channel trigger activation bits (CATx) are reset immediately after processing has started. It 

can be re-enabled first if corresponding channel processing has been finished. 

 

Activation of a channel via the register above should be done after the channel has been 

configured correctly. Internal processing holds the corresponding channel processing logic in 

reset state if the channel enable bit (CHENx) is not set. 

 

Summary of Contents for TAMC900








































































Reviews:

No comments