manualshive.com logo in svg

Tetan KP 12-ES, Service And Operation Manual

Share
Download
Tetan KP 12-ES Service And Operation Manual Download Page 18

Automatic boiler for wood pellets 

 

 

17 

 

  Attachment to both adaptors must be tight. 

Cleaning of KP62 burner

 provides removal of excessive ash or cinder volume from the burner when burning 

lower quality fuel. The drive of the cleaning mechanism is works together with ash cleaning. 

 Note:  

Use of alternate fuels requires change of the burner type and also change of boiler program setup. 

 Note: 

The cleaning mechanism burner drive and its installation are depicted in chapter 4.7 – Cleaning system. 

CERAMIC PARTS 

These parts are an inseparable component of the combustion chamber of the boiler and 

they have a major influence on the quality of burning. 

4.4.1

 

Ceramic reflector – placed on the top of the burner 

4.4.2

 

Ceramic secondary grate – placed in the boiler body above the burner heating chamber 

4.4.3

 

Ceramic plate – placed above the door 

4.4.4

 

Ceramic door jacketing– mounted on the door 

 

 

 

 

 

Picture No. 8   Cer. reflektor KP 12, KP 22 

 

 

Picture No. 9   Two-part cer. reflektor KP 62 

 
 

 

 

 

 

Picture No. 10   Ceramic secondary grade 

  

   

Picture No. 11   Ceramic shield   

 

 

Picture No. 12   Ceramic door casing 

Summary of Contents for KP 12-ES

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands