background image

ECOSTREAM PRIMER PUMP  

XTP3900/5600/7400/9200/10500/12000

VERSION March 2021

www.tetonus.com

800.752.0399

[email protected]

WELCOME TO THE WORLD OF TETON,  
NATURAL RELIABILITY™!

You Made The Right Choice Investing In This Quality 
Product. Thank You And Enjoy.

BEFORE USING THIS PRODUCT, PLEASE READ 
THESE INSTRUCTIONS CAREFULLY AND 
FAMILIARIZE YOURSELF WITH THE UNIT. PLEASE 
KEEP THESE INSTRUCTIONS IN A SAFE PLACE 
FOR FUTURE REFERENCE.

TECHNICAL SPECIFICATIONS

MODEL NO.

XTP3900

XTP5600

XTP7400

XTP10500

XTP12000

MAX FLOW RATE

3900 GPH

 

 

 

MAX HEAD

HEIGHT

 

 

 

 

 

 

WATTS

(MAX)

AMPS

VOLTS

OUTPUT HP

INTAKE/DISCHARGE

UNIONS INCLUDED

CORD

 

LENGTH

XTP9200

(14750 LPH)

5600 GPH

(21200 LPH)

7400 GPH

(28000 LPH)

9200 GPH

(34825 LPH)

10500 GPH

(39750 LPH)

12000 GPH

(45425 LPH)

195

350

600

620

830

970

1.8

5.3

5.6

7.3

8.6

115

115

115

115

115

115

1/8

1/4

1/2

1/2

3/4

1

2”

(5 cm)

2”

(5 cm)

2”

(5 cm)

3”

(7.5 cm)

3”

(7.5 cm)

3”

(7.5 cm)

8 ft

(2.4 m)

8 ft

(2.4 m)

8 ft

(2.4 m)

8 ft

(2.4 m)

8 ft

(2.4 m)

8 ft

(2.4 m)

17 ft

(5.2 m)

23 ft

(7.0  m)

26 ft

(7.9 m)

24 ft

(7.3 m)

23 ft

(7.0 m)

24 ft

(7.3 m)

3.2

Teton 

Page 2

Summary of Contents for Natural Reliability XTP Series

















Reviews: