Resi-Toner
Resi-Toner
Test-Um Inc.
Test-Um Inc.
The Intelligent Test Solutions Company
805-383-1500 /
FAX
805-383-1595 /
www.test-um.com
TU9858 (Rev A - 6/03)
808 Calle Plano / Camarillo, CA. 93012
TM
TM
RJ JACK
6-position modular jack
has line 2 on center pair,
pins 3 & 4. Line 1 is on
pins 2 & 5 plus the
alligator clip cable
.
DIAL TONE LED
On when POTS sim mode
is on. Flashes when on
with dial tone off
(talk battery)
DIAL TONE BUTTON
When in POTS Sim mode,
toggles dial tone between
enabled and disabled
with each press.
ALLIGATOR CLIP LEADS
POTS Sim Line 1
(Blk = TIP, Red = RING),
Speaker Pop signal and
Tone Gen signal,
Also on jack pins 2 & 5.
MODE SLIDE SWITCH
POTS SIM
SPEAKER POP
TONE GEN
-
-
-
Selects operating mode.
Press ON/OFF
to begin test.
Modes are:
Provides CO-like voltage,
current and dial tone
for 2 POTS lines.
Generates bursts of
current to create a popping
sound when connected
to a speaker.
Generates audio frequency,
sine-wave signal for
use with tone tracers.
LINE STATUS LEDs
Indicates when lines
are off-hook or shorted.
SPEAKER POP LED
On when speaker
pop is on.
BATTERY LOW LED
Replace battery soon.
Outputs will soon go
out of regulation.
TONE GEN LEDs
HI or LO LED will be
flashing when
generating tone.
Also indicate tone pattern
selected when in tone
selection mode.
ON/OFF BUTTON
Press to turn on in
the mode set by
the slide switch.
In tone gen mode,
hold button down to
enter tone pattern
selection mode and
release when
desired tone is selected.
OPERATING INSTRUCTIONS
4
1
Resi-Toner Operating Instructions
Part Number TG400
FEATURES
™
WARNING!
CAUTION!
Do not attach toACpower. The Resi-Toner™ may be damaged and cause a safety hazard for the user.
Improperly crimped, damaged or un-crimped plugs can damage the jacks on the Resi-Toner™. Inspect plugs for proper
termination and crimping before inserting into the tester. Contacts should always be recessed into the plastic grooves of
the plug. Do not use 6-position plugs with the 8-position (network) jack.
POTS Simulator
Talk Battery
Multiple dial tone
Speaker Pop
Sine-Wave Tone Generator
Unbalanced Tone
Three Tone Outputs
Constant Output
Auto-off
for two line phone system - line voltage, line current and dial tone.
mode of POTS Simulator provides more current than common tone generators.
sound for each line plus status indicators for off-hook and shorted.
function to ID speaker connections.
with two amplitude levels normal and half power
Reduces stray coupling to adjacent wires for better discrimination.
for stronger signal on twisted pairs - CAT 5 cables
selected from the front panel.
in all modes over the life of battery for 100% output all the time.
in any mode - no dead battery if left on.
Note
:
The RJ jumper “no-fault” cable, that has been provided with the Resi-Toner™, uses a unique colored modular
connector that can be plugged into a RJ11 jack or a RJ45 jack without damaging either jack. This allows
CAT 5 output points or phone lines using RJ45 jacks to be accessed without using an adapter.
Accessory Parts
Specifications:
-
All Lil' Buttie
series test set cords will work with the Resi-Toner
:
LB10 Lil' Buttie
cable set with alligator clips.
LB25 Lil' Buttie
cable set with piercing clips.
LB35 Lil' Buttie
cable set with bed-of-nails clips.
LB75 Telco Clip (requires drilling two holes in case)
Power Requirements: one 9 Volt alkaline battery
Battery Life (Alkaline, 540mA-hr) Times for exclusive use in:
Standby - 2 years
POTS Simulator, on-hook - 40 hours
POTS Simulator, off-hook - 8 hours
Speaker Popping - 40 hours
Tone Mode - 100 hours
Mechanical: Dimensions 4.5 x 1.75 x 1.3 inches, Weight 5.0 oz. with battery
On hook Voltage: 20VDC nominal
Off-hook Current (standard 430 ohm load): 21mA nominal
Dial Tone (into 600 ohms): 21dBM
Pop Energy: 0.044 Joules (Watt-Sec)
Peak Voltage: 20 Volts nominal
Tone frequencies (+/-1%): Dual 977Hz and 814Hz, Single 977Hz
Tone harmonics: Minimum of 40dB down from fundamental
Tone voltage, Typical (open circuit, new battery to 5.0V): LO = 4.6Vp-p, HI = 9.2Vp-p
Tone power, Typical (into 600 ohms, new battery to 5.0V): LO = -3dBM, HI = 3dBM
Test-Um Inc. guarantees to the end-user purchaser that its products will be free of all defects in material and/or workmanship.
This warranty extends for a period of 12 months for the test instrument and 3 months for the cables from the date of
manufacture or proof-of-purchase. The obligations of Test-Um Inc. under this warranty is limited to the repair or replacement
(at our option) during the warranty period, of any part that proves to be defective in material or workmanship under normal use,
installation and service, provided the product is returned to Test Um Inc. freight prepaid. A copy of the purchase receipt must
accompany products returned to us. In the absence of such a receipt, the warranty period will cease 12 months from the date of
manufacture. This warranty does not extend to products that have been subjected to neglect, accidental or improper use, or to
units which have been altered, repaired, or inspected by other than Test-Um authorized personnel. In no event will Test-Um Inc.
be liable for any incidental or consequential damages. The Resi-Toner™ is designed and manufactured to provide trouble free
service. However, if for some reason your tester should require repair, please follow these instructions.
All units returned for warranty repair will be repaired or replaced free of charge at the discretion of Test-Um Inc., and will be
shipped freight prepaid. In the event that a sales receipt or other dated proof-of-purchase documentation is not available, a
period of not more than 12 months from date of manufacture shall apply.
Damaged units returned for non-warranty repairs will be inspected and an estimated repair cost forwarded by phone or email.
Once an approval of these costs is received, the unit will be repaired. Charges for service and return freight will be invoiced on
a C.O.D. basis or by other prior arrangement.
™
™
™
™
™
1. Before returning any product to Test-Um Inc., you must first request a Return Merchandise Authorization Number (RMA) by
contacting our Customer Services Dept. at 805-383-1500. No shipments will be accepted without this number, which must be
clearly marked on the shipping label.
2. Ship the equipment with a copy of the sales receipt, if available.
3. Attach a description of the operational problem.
4. Include a contact name, phone number, and e-mail address (if possible).
5. Pack securely to prevent damage during shipping.
6. Ship prepaid to: Test-Um Inc, 808 Calle Plano, Camarillo, CA 93012
POTS SIMULATOR
SPEAKER POP
TONE GENERATOR
WARRANTY
WARRANTY SERVICE
NON-WARRANTY SERVICE
-
Shipping
