SAFETY GUIDE
Do not touch the body of the kettle when it is hot. Always hold the appliance by
the handle when using it.
Always ensure the lid is closed when in use. Failure to close the lid will prevent
the thermostat from switching off and cause the kettle to boil dry.
Keep the appliance well away from hot surfaces, and objects that can be
damaged by heat.
Ensure there is adequate room to operate the kettle and that steam can escape
safely.
Avoid contact with the steam from the spout when the water is boiling or just
after it has switched off.
Be careful when opening the lid for re-filling when the kettle is hot.
Ensure that the kettle cannot fall into water.
Do not fill or pour water from the kettle while it is on the base.
Disconnect the kettle at the mains supply before filling or emptying the jug,
before cleaning any of its components, and when it is not in use.
Do not immerse the connecting cord in water or other liquids.
Do not allow liquids to come into contact with the terminal pins of the kettle, its
base or the connecting cord.
Do not let the connecting cord overhang the edge of the work surface or allow it
to touch hot surfaces or sources of heat or flame.
If any part of this appliance is damaged or malfunctions in any way, or the
connecting cord or mains plug is broken do
not
continue to use it. Seek expert
assistance.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliances by a person responsible for their safety
Children should be supervised to ensure that they do not play with the
appliance.
CAUTIONS
Do not place the power base unit on a metal tray or metal surface when
plugged into any power source.
This appliance is for indoor domestic use only. Do not use it outdoors.
This kettle jug and power base form an integral appliance. Do not use other
kettle jugs with this power base, or this kettle jug with other bases.
The switch on this appliance must be readily operable at all times.
Do
not hinder its operation by incorrect placement or by placing obstacles that
may restrict its free movement.
PRELIMINARIES
Unpack your kettle and any accessories carefully. Retain the packaging so that
you can transport the appliance safely. If you dispose of it please do so with
regard to any recycling regulations in your area.
Before using your kettle:
Check that the voltage marked on the rating plate under the kettle or the base
matches your mains voltage. Please read all the instructions in this User Guide
with particular reference to the safety notes.
CONNECTING AND USING THE KETTLE
Separate the kettle from the base.
Ensure that the mains socket is switched off at the wall. Lead the power cord
out through the recess in the base. Place the kettle base on a stable level
surface and connect the power cord to the wall socket. Excess cord may be
safely stowed by feeding it carefully into the stowage compartment in the
base.
Ensure the power cable exits through the three cut out slot in the
base otherwise the kettle will not be stable.
Pour away previously boiled water and use fresh water to fill the kettle.
Gently pull the kettle release back to open the lid. Fill the kettle to the desired
level through the lid. Close the lid.
The water level must always cover the lowest mark on the gauge. Do NOT fill
the kettle above the
MAX
mark (1.7 litres) or boiling water may be ejected.
If
you cannot see the water level through the scale,the level is incorrect.
Position the filled kettle correctly on the power base.
Boiling the Kettle
Before first use or after storage:
Fill the kettle with fresh water. Boil the water. Pour away the boiled water.
Repeat this two or three times. The kettle is now ready for use.
Switch on the power at the wall socket.
The kettle
ON/OFF
switch is located below the handle.
Press this down to switch the kettle on. The water gauge
will illuminate showing the kettle is operational.
When the water has reached the desired temperature, the kettle will switch off
automatically. You can stop the boiling at any time by lifting the switch up.
To re-boil, depress the switch again. If the water is very hot, it may be
necessary to wait until the switch resets.
Always ensure the lid is tightly fitted and never lift it while the kettle is boiling
or you run the risk of scalding. If the lid is not correctly fitted while boiling, the
automatic cut-out will not operate and you may boil the kettle dry.
After boiling, switch off the appliance at the mains.
The kettle may now be safely removed from its base and the boiled water
poured out. Always take care to pour boiling water slowly and carefully
without tipping the kettle too quickly. Never leave hot water in the kettle while
it is unattended.
After use, replace the kettle on its base.
KEY
5: Handle
1: Spout
6: ON/OFF Switch
2: Water Filter (In Spout)
7: Water Gauge
3: Kettle Lid Release
8: Kettle Base
4: Kettle Lid
9: Kettle Jug
DESCRIPTION
b
c
d
e
f
g
h
i
j
Summary of Contents for JKRP10R
Page 2: ...0 ...
