background image

FAULT FINDING

The table below should help solve any problems, which may be 
stopping your lift from operating correctly. If, however, your lift 
still does not operate correctly after referring to this table please 
do not hesitate to call the number on the back of this booklet for 
further advice.

Lift 

Position

Problem

Cause

Remedy

Lower level

Lift will not 

operate

Charger isolation 

switch disabling 

lift

Remote control 

enabler(if fitted) 

not activated.

Ensure charger 

isolation switch 

is on.

Activate remote 

control enabler

with key fob.

Lift rises short 

distance then 

stops

Obstruction on 

ramp

Remove 

obstruction on 

ramp

Upper level

Lift will not 

operate

Charger isolation 

switch disabling 

lift.

Remote control 

enabler(if fitted) 

not activated

Ensure charger 

isolation switch 

is on.

Activate remote 

control enabler 

with key fob

Upper level 

gate not closed 

properly (where 

fitted)

Ensure gate is 

fully closed

Platform safe 

edge obstructed

Remove 

obstruction 

below the lift

Lift operates but 
stops before the 

lower level

Platform safe 

edge obstructed

Remove 

obstruction 

below the lift

11

Summary of Contents for TSL1000

















Reviews: