![Terrasat IBUC 3 Operation Manual Download Page 79](http://html.mh-extra.com/html/terrasat/ibuc-3/ibuc-3_operation-manual_1089882079.webp)
M&C Interfaces
|
5-9
Engineered to Endure
3. Type the password command
CPE=1234
.
You can now use ASCII commands to configure and monitor the IBUC. For more
Web Server
You can access embedded Web pages that contain status and configuration
information.
Connect to the IBUC M&C and type the IP address of the IBUC through a Web
browser. A login page then appears. After login, you have a choice of eight Web pages
(nine pages if using redundant IBUCs) with monitoring, control and alarm
information. Individual pages are displayed by clicking the tabs at the top of the Web
page frame. On a redundant transmit system, the display area will contain two frames.
The left side will display the A: side IBUC and the right will display the B: side IBUC.
To initiate a embedded Web page session,
1. Activate a Web browser window from the host computer.
2. Type the IP address of the IBUC in the address window and then press Enter. For
more information about the options available on each Web page, see
.
SNMP
The IBUC
3
and IBUC
3
G
supports both version 1.0 & 2.0c of the SNMP protocol.
The SNMP agent listens on Port 161 for messages and uses Port 162 for transmitting
trap information. SNMP can be configured from the HHT, RS232, Telnet, Web pages,
FSK and the RS485 interfaces (ASCII Mode required for FSK and RS845). The MIB-
II system group is implemented.
To configure SNMP using the Hand-held terminal (HHT),
1. Connect the HHT to the IBUC by using the 19-pin connector.
2. Press the decimal key four times (e.g: “
. . . .
”).
3. Type the password. The default password is 1234.
4. Press the right arrow key to access the SNMP submenu.
5. Press the up/down keys until the “Enable SNMP” selection appears and press
Enter
to configure “Enable SNMP’ selection.
6. Press Yes to enable SNMP.
7. Press the Bksp key.
8. Navigate with up/down keys to the “Trap Host1” selection and press
Enter
to
configure it.
9. Press Yes to enable traps.
Summary of Contents for IBUC 3
