background image

10

Service type

Description

0x00

reserved for future use

0x01

digital television service (see note 1)

0x02

digital radio sound service (see note 2)

0x03

Teletext service

0x04

NVOD reference service (see note 1)

0x05

NVOD time-shifted service (see note 1)

0x06

mosaic service

0x07

FM radio service

0x08

DVB SRM service [49]

0x09

reserved for future use

0x0A

advanced codec digital radio sound service

0x0B

H.264/AVC mosaic service

0x0C

data broadcast service

0x0D

reserved for Common Interface Usage (CENELEC EN 50221 [37])

0x0E

RCS Map (see ETSI EN 301 790 [7])

0x0F

RCS FLS (see ETSI EN 301 790 [7])

0x10

DVB MHP service

0x11

MPEG-2 HD digital television service

0x12 to 0x15

reserved for future use

0x16

H.264/AVC SD digital television service

0x17

H.264/AVC SD NVOD time-shifted service

0x18

H.264/AVC SD NVOD reference service

0x19

H.264/AVC HD digital television service

0x1A

H.264/AVC HD NVOD time-shifted service

0x1B

H.264/AVC HD NVOD reference service

0x1C

H.264/AVC frame compatible plano-stereoscopic HD digital television service (see note 3)

0x1D

H.264/AVC frame compatible plano-stereoscopic HD NVOD time-shifted service (see note 3)

0x1E

H.264/AVC frame compatible plano-stereoscopic HD NVOD reference service (see note 3)

0x1F

HEVC digital television service (see note 4)

0x20 to 0x7F 

reserved for future use

0x80 to 0xFE 

user defined

0xFF

reserved for future use

NOTE 1

: MPEG-2 SD material should use this type. 

 

NOTE 2

: MPEG-1 Layer 2 audio material should use this type. 

 

NOTE 3

: For information on the use of these values, see clause I.2.3 and ETSI TS 101 547-2 [54] 

               (3D Guidelines of Frame Compatible 3D-TV). 

 

NOTE 4

: For information on the use of these values, see clause I.2.5 and ETSI TS 101 547-4 [62].

Figure 17. Service type coding

Summary of Contents for tdq4168



















Reviews: