Terex Genie Z-40 Service And Repair Manual Download Page 93

Page: 93 / 287

June 2022

Service and Repair Manual

Manifolds

Part No. 1268555GT

-62/40

How to Test a Coil Dio de

How to Test a Coil Diode

Properly functioning coil diodes protect the

electrical circuit by suppressing voltage spikes.

Voltage spikes naturally occur within a function

circuit following the interruption of electrical current

to a coil. Faulty diodes can fail to protect the

electrical system, resulting in a tripped circuit

breaker or component damage.

Electrocution/burn hazard.

Contact with electrically charged

circuits could result in death or

serious injury. Remove all rings,

watches and other jewelry.

1 Test the coil for resistance. Refer to Repair

Procedure,

How to Test a Coil

2 Connect a 10W resistor to the negative

terminal of a known good 9V DC battery.

Connect the other end of the resistor to a

terminal on the coil.

Resistor 10

Genie part number 27287

Note: The battery should read 9V DC or more

when measured across the terminals.

1  multimeter
2  9v DC battery
3  10

resistor

4 coil

Note: Dotted lines in illustration indicate a reversed

connection as specified in step 6.
3 Set a multimeter to read DC current.
Note: The multimeter, when set to read DC

current, should be capable of reading up to

800 mA.
4 Connect the negative lead to the other

terminal on the coil.

5 Momentarily connect the positive lead from

the multimeter to the positive terminal on the

9V DC battery. Note and record the current

reading.

6 At the battery or coil terminals, reverse the

connections. Note and record the current

reading.

Result: Both current readings are greater than

0 mA and are different by a minimum of 20%.

The coil is good.

7 Result: If one or both of the current readings

are 0 mA, or if the two current readings do not

differ by a minimum of 20%, the coil and/or its

internal diode are faulty and the coil should be

replaced.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands