manualshive.com logo in svg

Terex Genie Z-40, Service And Repair Manual

The Terex Genie Z-40 Service and Repair Manual is the go-to resource for maintaining and fixing your Z-40 model. Find this comprehensive manual on manualshive.com, available for instant download. Ensure the longevity and performance of your equipment with this invaluable tool, conveniently accessible and absolutely free.

Share
Download
background image

Service and Repair Manual

 

June 2022

 

Manifolds 

 

 

60 

Z

®

-62/40

 

Part No. 1268555GT 

 

 

8-2 Valv e Adjust men ts -  Fu nction  Ma nifold  

8-2   

Valve Adjustments - Function 

Manifold 

How to Adju st th e Syste m Relie f Valve  

How to Adjust the System Relief 

Valve 

Note: Perform this procedure with the machine in 

the stowed position. 
1  Connect a 0 to 5000 psi / 0 to 350 bar 

pressure gauge to the test port on the function 

manifold. 

2  Start the engine from the ground controls. 
3  Press and hold the function enable button. 

Activate and hold the primary boom retract 

switch with the boom fully retracted.   

4  Observe the pressure reading on the pressure 

gauge. Refer to Specifications,

 Hydraulic 

Component Specifications

. 

5  Turn the engine off. Use a wrench to hold the 

relief valve and remove the cap. 

6  Adjust the internal hex socket. Turn it 

clockwise to increase the pressure or 

counterclockwise to decrease the pressure. 

Install the relief valve cap. 

 

Tip-over hazard. Do not adjust 

the relief valve higher than 

specified. 

7  Repeat this procedure beginning with step 

2 to confirm the relief valve pressure. 

8  Remove the pressure gauge. 

How to Adju st th e Platfo rm  Lev el Up Reli ef Valve  

How to Adjust the Platform Level 

Up Relief Valve 

Note: Perform this procedure with the machine in 

the stowed position. 
1  Connect a 0 to 5000 psi / 0 to 350 bar 

pressure gauge to the test port on the function 

manifold. 

2  Start the engine from the ground controls. 
3  Set the engine speed to high rpm. 
4  Raise the jib to the horizontal position. 
5  Press and hold the function enable button. 

Activate and hold the platform level up switch 

with the platform fully elevated. 

6  Observe the pressure reading on the pressure 

gauge. Refer to Specifications,

 Hydraulic 

Component Specifications

. 

7  Turn the engine off. Use a wrench to hold the 

relief valve and remove the cap. 

8  Adjust the internal hex socket. Turn it 

clockwise to increase the pressure or 

counterclockwise to decrease the pressure. 

Install the relief valve cap. 

9  Repeat this procedure beginning with step 

2 to confirm the relief valve pressure. 

10  Remove the pressure gauge. 

Summary of Contents for Genie Z-40
































































































































































































































































































Reviews:

No comments

Related manuals for Genie Z-40

QUALITY LIFTS MID-RISE LIFT Installation, Operation And Maintenance Manual preview
MID-RISE LIFT
Brand: QUALITY LIFTS Pages: 13
Sinoboom GTJZ0608 Operation Manual preview
GTJZ0608
Brand: Sinoboom Pages: 37
Launch TLT830WA User Manual preview
TLT830WA
Brand: Launch Pages: 12
TLS TLSS16ALORR1 Instructions & Operating Manual preview
TLSS16ALORR1
Brand: TLS Pages: 30
TLS TLSS10ALORR1 Installation, Operation & Service Manual preview
TLSS10ALORR1
Brand: TLS Pages: 30
Mec 45-AJ Diesel Operator'S Manual preview
45-AJ Diesel
Brand: Mec Pages: 48
Mec 3084ES Operator'S Manual preview
3084ES
Brand: Mec Pages: 56
Mec 45-J Diesel Service & Parts Manual preview
45-J Diesel
Brand: Mec Pages: 260
JLG Power Towers Nano Operating And Maintenance Manual preview
Power Towers Nano
Brand: JLG Pages: 24
JLG TOUCAN DUO Service Manual preview
TOUCAN DUO
Brand: JLG Pages: 108
JLG Toucan 12E Operation And Safety Manual preview
Toucan 12E
Brand: JLG Pages: 136
JLG Skytrak 3013 Operation & Safety Manual preview
Skytrak 3013
Brand: JLG Pages: 136
JLG GRADALL 544D-10 Operation & Safety Manual preview
GRADALL 544D-10
Brand: JLG Pages: 142
JLG H340AJ Operation And Safety Manual preview
H340AJ
Brand: JLG Pages: 144
JLG G10-43A Operation & Safety Manual preview
G10-43A
Brand: JLG Pages: 170
JLG X20JPLUS Operator, Safety, Maintenance And Service Manual preview
X20JPLUS
Brand: JLG Pages: 206

Brands by name

Popular brands

Load more brands