Terex Genie Z-40 Service And Repair Manual Download Page 58

Page: 58 / 287

Service and Repair Manual

June 2022

Engines

-62/40

Part No. 1268555GT

5 Support the engine with an overhead crane or

other suitable lifting device. Do not lift it.

6 Remove the engine mounting plate to bell

housing fasteners.

7 Raise the engine slightly using the overhead

crane and place a block of wood under the oil

pan for support.

8 Support the drive pump assembly with an

overhead crane or other suitable lifting device.

Do not apply any lifting pressure.

9 Remove all of the engine bell housing

retaining fasteners.

10 Carefully pull the pump and bell housing

assembly away from the engine and secure it

from moving.

Perkins models:

1 Remove the fuel filter/water separator

mounting fasteners.

2 Remove the fuel filter/water separator and lay

it to the side. Do not disconnect the hoses.

3 Support the drive pump assembly with an

appropriate lifting device.

4 Remove all of the engine bell housing

fasteners.

5 Carefully pull the pump and bell housing

assembly away from the engine and secure it

from moving.

Component damage hazard.

Hoses can be damaged if they

are kinked or pinched.

6 Remove the flex plate mounting fasteners.
7 Remove the flex plate from the flywheel.

How to I nstall t he Flex Plat e

How to Install the Flex Plate

1 Install the flex plate onto the engine flywheel

with the rubber vibration isolators towards the

pump.

2 Apply Loctite

removable thread sealant to

the flex plate fasteners and loosely install the

fasteners.

Deutz models:

Torque the flex plate

mounting bolts in sequence to 28 ft-lbs / 38

Nm. Then torque the flex plate mounting bolts

in sequence to 40 ft-lbs / 54 Nm.

Ford and Perkins models:

Torque the flex

plate mounting bolts in sequence to 14 ft-lbs /

19 Nm. Then torque the flex plate mounting

bolts in sequence to 20 ft-lbs / 27 Nm.

4 Apply a high viscosity coupling grease (Genie

part number 128025) to the splines of the

pump shaft and flex plate.

Grease Specification

Shell Alvania

Grease CG, NLGI 0/1 or equivalent.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands