Terex Genie Z-40 Service And Repair Manual Download Page 5

Page: 5 / 287

June 2022

Service and Repair Manual

Safety Rules

Part No. 1268555GT

-62/40

Secti on 1

Safety Rul es

Gene ral Saf ety Rul es

Danger

Failure to obey the instructions and safety

rules in this manual and the appropriate

Operator's Manual on your machine will result

in death or serious injury.
Many of the hazards identified in the

operator's manual are also safety hazards

when maintenance and repair procedures are

performed.
Do not modify or alter a MEWP without prior

written permission from the manufacturer.

Do Not Perform Maintenance

Unless:



You are trained and qualified to perform

maintenance on this machine.



You read, understand and obey:

•

manufacturer's instructions and safety

rules

•

employer's safety rules and worksite

regulations

•

applicable governmental regulations



You have the appropriate tools, lifting

equipment and a suitable workshop.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Terex Genie Z-40, Service And Repair Manual, Page: 5 / 287

Search results

Summary of Contents for Genie Z-40

Reviews: