Terex Genie Z-40 Service And Repair Manual Download Page 15

Page: 15 / 287

June 2022

Service and Repair Manual

Specifications

Part No. 1268555GT

-62/40

Secti on 2

Specificatio ns

Machin e Specific atio ns

Machine Specifications

Tires and Wheels

Tire size (Rough terrain)

355/55D625

Tire weight, new foam-filled

(Rough terrain) (minimum)

415 lbs

188 kg

Tire size (High flotation)

41/18LL x 22.5

Tire ply rating

(Rough terrain and Hi-flotation)

Wheel lugs

9 @ 5/8 - 18

Lug nut torque, dry

240 ft-lbs

325 Nm

Lug nut torque, lubricated

180 ft-lbs

244 Nm

Overall tire diameter (Rough terrain)

36.9 in

93.7 cm

Overall tire diameter (High flotation)

40.3 in

102.4 cm

Tire pressure (Rough terrain)

70 psi

4.92 bar

Tire pressure (High flotation)

60 psi

4.13 bar

Track Components

Track material

Rubber

Tensioning system

Pressurized grease

Weight (each)

1500 lbs

680 kg

Fluid capacities

LPG tank

33.5 lbs

15.2 kg

Fuel tank (Gas / LPG models)

20 gallons

75.7 liters

Fuel tank (Diesel models)

36 gallons

136.3 liters

Hydraulic tank

35 gallons

132.5 liters

Hydraulic system (including tank)

45 gallons

170.3 liters

Drive hubs

20 fl oz

591 cc

Turntable rotation drive hub

43 fl oz

1262 cc

Drive hub oil type: SAE 90 multipurpose hypoid gear oil

API service classification GL5

For operational specifications, refer to the

Operator's Manual.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Terex Genie Z-40, Service And Repair Manual, Page: 15 / 287

Search results

Summary of Contents for Genie Z-40

Reviews: