background image

 

1-3

 

 Caution

 

 

Check that the delivered items are exactly what you 
ordered. 

The use of a wrong product may cause an injury or failure. 

Do not place any combustibles around the product.

Otherwise, it may lead to a fire. 

 

Do not place any obstacles around the product that 
may hinder ventilation. 

Otherwise, it may lead to a fire. 

Do not touch the impeller, tie bolt, or other parts of 
the pump with bare hands. 

Otherwise, it may lead to an injury or damage. 

 

Do not run the pump at a frequency exceeding 60 
Hz. 

Otherwise, it may lead to motor burnout or a fire. 

Do not use the unit for pumping any fluids beyond 
the specified viscosity limit. 

Otherwise, it may lead to motor burnout or a fire. 

 

Ensure to install an overcurrent protective device. 

The user is required by the technical standards for electrical 
facilities to install one. Otherwise, it may damage the product, 
thus leading to a fire or failure.

 

It is also recommended to 

install protective devices such as a ground fault interrupter. 

Do not touch any terminals or wires when 
measuring the insulation resistance. 

Otherwise, it may lead to an electric shock. 

 

Do not use thinner or benzine for cleaning the 
product. 

Otherwise, the product may be discolored or its coating may 
be peeled off. 

Once you turn off the power, wait until the pump 
stops completely. Do not restart the pump until it 
does. 

Otherwise, the main shaft may be subjected to an excessive 
load, which makes the service life of the pump shorter. 

 

When you hoist the product, pay attention to its 
center of gravity. 

Otherwise, the product may topple over or fall, thus leading to 
an injury. 

If you use a solvent for cleaning the product, pay 
attention to handling of the solvent as well as the 
environment of use. 

Otherwise, it may lead to poisoning. 

 

When you lift the product by hand, pay attention to 
its weight. Do not allow a single person to lift a 
product heavier than 15 kg. 

Otherwise, it may put strain on the body, thus leading to an 
injury. 

Dispose of the product as industrial waste. 

 

Be sure to conduct inspection according to the 
Maintenance checklist. 

Otherwise, you cannot prevent potential failures, thus leading 
to a higher risk of accidents.

 

For star-delta starting, use a starter with an 
electromagnetic switch (three-contactor type) on the 
primary side. 

Otherwise, it may lead to a fire. 

 

1.3  Location of warning labels and caution labels 

The figure shows the locations of warning labels and caution labels. If these labels become dirty and 
illegible or if they are peeled off, replace them with a new one. 
 

Warning

 

Caution

 

Observe all the instructions in the warnings and cautions affixed to the 
machine as well as those described in this instruction manual. 

VKN115A-e

VKP115A-e

Electric shock 
caution label 

RoHS label

Pump nameplate

Motor nameplate

Pump nameplate

Electric shock 
caution label 

RoHS label 

Motor nameplate 

Summary of Contents for VKN-e Series

































Reviews: