background image

OPERATION

21

810D MM310 (3--95)

MAIN BRUSH SHUT DOWN LIGHT

The main brush shut down light

comes on

when there is excessive down pressure for the

main brush, or there is a problem with the main

and side brush hydraulic motor circuit. The brush

pressures can be reduced with the main brush

and side brush pressure knobs.

CLOGGED FILTER LIGHT

The clogged filter light

comes on when the

hopper dust filter is clogged. If the machine is

equipped with a Regenerative Filter System

(RFS) option, the light will remain on for a few

seconds each time the RFS cycles.

To clean the filter, press the filter shaker switch. If

the clogged filter light remains lit, manually clean

the hopper dust filter. See

HOPPER DUST

FILTER

in

MAINTENANCE.

HOPPER DOOR LIGHT (OPTION)

The hopper door light

comes on when the

hopper door is open. Make sure the hopper door

is closed and the hopper door light is off, before

sweeping with the machine.

FUEL LEVEL GAUGE

The fuel level gauge

indicates how much fuel

is in the fuel tank with a segmented LED light.

When the tank is full, all ten of the segments are

lit. As the fuel tank empties, the segments shut

off. The fuel tank is empty when all ten of the

segments have shut off.

NOTE: Do not let the fuel tank empty completely.

Air can enter the fuel system. The fuel system will

need bleeding before the next engine start.

07761

07762

07763

07764

Summary of Contents for 810D































































































Reviews: