MAINTENANCE
1550 Gas/LPG/Diesel MM283 (9--01)
3--44
SQUEEGEES
SIDE SQUEEGEES
The side squeegees control scrub brush water
spray. They consist of a squeegee blade, backup
strip, band, and clamp. Check the side squeegee
blades for damage or wear daily. Replace
squeegee blade by opening the quick-release
latch and removing the band. Remove the
bracket, old blade, and backup strip. Replace the
squeegee blade and backup strip if the blade is
worn.
Adjust the squeegee clamp so that there is
adequate pressure to hold the squeegee blade in
place. The squeegee blade should be held so that
it cannot be pulled from between the locating pins.
D
A
C
I H
E
F
G
B
00302
SIDE SQUEEGEE ASSEMBLY
A. Retaining Band
B. Latch
C. Door Locking Pin
D. Door
E. Flap
F. Door Latch
G. Squeegee Frame
H. Backup Strip
I. Squeegee Blade
The side squeegee frame is attached to the
squeegee door with four screws. The screw
mounting holes are slotted, allowing vertical
adjustment of the squeegee blade by simply
loosening the screws and moving the squeegee
up or down. Check the side squeegee blades
adjustment daily.
Lower the head and adjust the squeegee so that
the blade deflects 0.50 in (13 mm). The squeegee
should deflect evenly across its entire length.
A
B
00289
SQUEEGEE BLADE DEFLECTION
A. Squeegee Blade
B. 0.50 in (13 mm) Deflection
SCRUB HEAD REAR SQUEEGEES
The scrub head rear squeegees control scrub
brush water spray and channels water into the
rear squeegee path. Check the squeegee blades
for damage or wear daily. Replace the squeegee
blade if it is worn by removing the cotter pin and
clevis pin which hold the squeegee assembly to
the mounting bracket. Then remove the cotter pin,
clevis pin and retaining clip which holds the
squeegee blade onto the squeegee frame.
A
B
C
D
E
F
F
E
G
06941
SCRUB HEAD REAR SQUEEGEES
A. Squeegee Blade
B. Squeegee Frame
C. Mounting Bracket
D. Retaining Clip
E. Cotter Pin
F. Clevis Pin
G. Scrub Head
The scrub head rear squeegee assemblies are
each mounted to the scrub head with two screws.
The mounting brackets have slots in them for
vertical adjustment. Loosen the two screws and
adjust the squeegee assemblies to get the proper
deflection. Then tighten the screws. Check the
squeegee blade adjustment daily.
Summary of Contents for 1550
