Tenda FH456 Page 7 User Manual Download

Page: 7 / 82

Get to Know Your Router

3 Buttons & Interfaces

(Take FH456V2.0 as an example. Your product may differ.)

LED Indicator

Status

Description

SYS

Blinking

The system is working fine.

Off

There is no power supply, or the router malfunctions.

WiFi

Solid

WiFi is enabled.

Blinking

The Router is transmitting WiFi data.

Off

WiFi is disabled.

1/2/3

Solid

The LAN port is well connected.

Blinking

The LAN port is transmitting data.

Off

No link is detected on the LAN port.

WAN

Solid

The WAN port is well-connected.

Blinking

The WAN port is transmitting data.

Off

No Ethernet cable is connected to the WAN port.

WPS

Solid

WPS is enabled, or a WPS connection is established.

Blinking

The Router is performing WPS negotiation to a client device, or transmitting
data.

Off

WPS is disabled.

Summary of Contents for FH456



















































































Search results

Summary of Contents for FH456

Reviews:

Related manuals for FH456

Brands by name

Popular brands

Tenda FH456, User Manual

Search results

Summary of Contents for FH456

Reviews:

Related manuals for FH456

Brands by name

Popular brands