ISD 80/95/110/140 K-DN
(c/w SAT-2 Controller)
Ducted Split System
Indoor Units
Installation &
Maintenance
GENERAL
These ISD
S
K-DN indoor units are designed
to be coupled with the OSA
S
RK outdoor
units. The '-DN' indicates the unit is supplied
complete with SAT-2 room temperature
controller and safety drain tray.
Units must be installed in accordance with
all national and local safety codes.
Combinations
One ISD 81K with one OSA 80RKS
One ISD 95K with one OSA 95RKS
One ISD 110K with one OSA 110RKS
One ISD 110K with one OSA 110RKT
One ISD 140K with one OSA 140RKT
Options
1. Filter Box c/w polypropylene net filter
2. Spring Mounting Kit
3. Electric Heater Box
4. Supply & Return Air Plenums
5. SAT-2 Accessories (refer overleaf).
SAFETY DRAIN TRAY
The unit is supplied with a safety drain tray
to protect your ceiling against accidental
damage. The safety drain tray is best
secured to the ISD unit
after the unit has
been suspended in the ceiling, however it
is possible to fit it
before if circumstances
make this easier.
AIR FILTRATION / FILTER BOX (Option)
As air filtration requirements vary, filters are
not supplied with the unit. Filters should
ideally be installed on the return air side of
the unit, no closer than 500mm from the
back of the unit and easily accessible for
cleaning. To maximise the efficiency of air
flow, the return air filter should be twice the
area of the ISD unit's return air spigot/s. If
efficiency is less of a concern a Filter Box is
available.
The Filter Box is installed by unscrewing
the return air spigot and replacing it with
the Filter Box's filter-integrated spigot. The
filter may be accessed from either side of
this spigot. This new spigot has a depth of
135 mm, instead of 60 mm.
ELECTRIC HEATER BOX (Option)
The Electric Heater Box is installed by
unscrewing the supply air spigot and
replacing it with the Electric Heat Box's
element-integrated spigot. This new spigot
has a depth of 195 mm, instead of 60 mm.
A separate page of installation instructions is
supplied with the Kit.
INSTALLATION
Positioning & Mounting
Provide 500 mm minimum clearance to both
ends of the unit.
Fig. 1 Dimensions (mm)
Not to Scale
PROJECTION
ISD 80K, 91K, 110K, 140K
Fig. 2 Spring Mounting
Fig. 3 Solid Mounting
RECOMMENDED
MOUNTING
SYSTEM
(OPTIONAL
EXTRA)
Fig. 4
OPEN
DRAIN
MINIMUM
SLOPE
20 mm PER m
(1 IN 50)
50 mm
MINIMUM
100 mm
APPROX.
'U' TRAP
100 mm
APPROX.
VENT PIPE
FOR LONG
CONDENSATE
DRAIN RUNS
UNIT
Note: The Safety Drain Tray
does not require trapping.
REFRIGERANT
CONNECTIONS
E
OVERALL
50
420 OA
225
335
60
30
DRAIN 19 OD
30
650 OA
400
482
MOUNTING
CENTRES
B
ELECTRICAL
CONDUIT HOLE
(BOTH ENDS)
60
60
FAN ACCESS VIA
REMOVEABLE BASE
& DRAIN TRAY
ACCESS
PANEL
ELECTRICAL
BOX
170
ELECTRICAL
BOX
C
FIXED MTG CTRS
D
500 MIN. CLEARANCE
500 MIN. CLEARANCE
F
Condensate Drain
Net Weight
ISD 80K 36 kg
ISD 91K 39 kg
ISD 110K 40 kg
ISD 140K 46 kg
TIGHTEN
LOCKNUTS
FOR
STRENGTH
MOUNTING ROD
MOUNTING
BRACKETS
SUPPLIED
B
125
175
240
240
A
570
660
787
787
C
747
836
962
962
MODEL
ISD 80K
ISD 95K
ISD 110K
ISD 140K
D
805
895
1020
1020
E
835
925
1050
1050
F
190
230
290
290