PLATFORM GUIDE
HIPSWITCH™-100 SERIES
Industrial Security Appliances
HIPswitch™-100 Series
EN
DOC-0053-A
PLATFORM GUIDE
Revision Date: April 7, 2017
WIRING
Power Inputs
This device supports dual redundant power supplies, power supply 1
(PWR 1) and power supply 2 (PWR 2). The connectors for PWR 1 and
PWR 2 are located on the terminal block.
Step 1
: Insert the negative DC into the V- terminal and the positive DC
into the V+ terminal.
Step 2
: To keep the DC wires from pulling loose, use a small flat-blade
screwdriver to tighten the wire-damp screws in the front of the terminal
block connector.
Serial Connector
(-s models only)
Pin #
RS-232
RS-422
RS-485
(4-wire)
RS-485
(2-wire)
1
DCD
Tx-
Tx-
DATA-
2
RxD
Tx+
Tx+
DATA+
3
TxD
Rx+
Rx+
N/C
4
DTR
Rx-
Rx-
N/C
5
GND
GND
GND
GND
6
DSR
N/C
N/C
N/C
7
RTS
N/C
N/C
N/C
8
CTS
N/C
N/C
N/C
9
RI
N/C
N/C
N/C
Use only with IEEE 802.3af compliant power sources. Power over Ethernet is optional on port 1.
DO NOT
attempt to apply Power over Ethernet on port 2
Power over Ethernet Warning
Status LED Codes
Normal Operation
On Steady
No Conductor Connection
O O O O = = O O = =
Conductor Blink
O O = =
System Error
O O O O = = O O O = =
Missing Identity
O O O = = O = =
Secure Network Error
O O O O = = =
Factory Reset
O O = = O = =
No Shared Network
O O O O = = O = =
Diagnostic Mode
O = O =
(fast blink)
Downloading Firmware
O O O = = O O = =
Updating Firmware
O O O = = =
O
Blink
=
Pause
DIMENSIONS
PACKAGE CONTENTS
Qty
Item
x1
HIPswitch-100
x1
DIN-rail kit (attached)
Qty
Item
x2
Wall-mount kit
x2
4-pin terminal block
1. Power input connector
2. SIM slot (100g only)
3. LED: Power input #1 indicator
ON = Activated
4. LED: Power input #2 indicator
ON = Activated
5. LED: PoE indicator
ON = Power supplied over Ethernet
on port 1
6. LED: Link and activity for port 1
ON = Port is linked
Blinking = Data is being transmitted
7. LED: Link and activity for port 2
ON = Port is linked
Blinking = Data is being transmitted
8. LED: Blink = Cellular modem ready
9. LED: Status (see Status Codes)
10. Multi-purpose button
(see Multi-purpose button table)
11. Ethernet port 2
12. Ethernet port 1
(optional PoE)
13. Aux. cellular antenna connector
(100g only)
14. LED: Serial receive activity (-s models only)
15. LED: Serial transmit activity (-s models only)
16. Serial connector (-s models only)
17. Main cellular antenna connector (100g only)
TOP & FRONT PANEL LAYOUTS
MULTI-PURPOSE BUTTON
NOTE
: Some Tempered Networks documents may refer to this as a “Reset” button.
The multi-purpose button provides two different functions, depending on how long it is pressed and
held.
Short Tap
Press for 3 seconds and release. The Status LED will now
blink steadily.
Places the HIPswitch
in diagnostic mode.
Long Tap
Press for at least 8 seconds and release. The Status LED
will now blink in a 2 flash, 1 flash pattern,
Resets the HIPswitch
to factory defaults.
NOTE
: To exit diagnostic mode, press the reboot button in the diagnostic interface or cycle the input
power of the HIPswitch.
Part Number
Model
10/100
Ethernet
4g
Cellular
Serial
802.3af PoE
101e-201
HIPswitch-100e
2
No
No
Yes
101g-201
HIPswitch-100g
2
Yes
No
Yes
101e-s-201
HIPswitch-100e-s
2
No
Yes
Yes
101g-s-201
HIPswitch-100g-s
2
Yes
Yes
Yes
The HIPswitch™-100 Series is a small form
factor industrial grade security appliance
that facilitates private overlay networks
between customer-provided equipment and
devices. This document contains import
-
ant operating information, specifications,
and installation instructions for the HIP
-
switch™-100.
MODELS
HIPswitch™-100 Series
Safety and Warnings
Elevated Operating Ambient
: If instslled in a closed environment, make sure the
operating ambient temperature is compatible with the maximum ambient temperature
specified by the manufacturer.
Reduced Air Flow
: Make sure the mount of air flow required for safe operation of the equipment
is not compromised during installation.
Mechanical Loading
: Make sure the mounting of the equipment is not in a hazardous condition
due to uneven mechanical loading.
Circuit Overloading
: Consideration should be given to the connection of the equipment to the
supply circuit and the effect that overloading of the circuits might have on over-current protection
and supply wiring. Appropraite considertation of equipment nameplate ratings should be used
Explosion Hazard
: Do not disconnect equipment unless power has been removed or the area is
known to be non-hazardous.
e-mail:
Phone:
+1 206.452.5500 ext. 2
www.temperednetworks.com
3101 Western Ave.
Ste. 550
Seattle, WA 98121
Hardened. Resilient. Simple.
