background image

Installation Instructions and 

Homeowner’s Manual

20007894  5/08   Rev.  7

DO NOT STORE OR USE 
GASOLINE OR OTHER 
FLAMMABLE VAPORS AND 
LIQUIDS IN THE VICINITY OF 
THIS OR ANY OTHER 
APPLIANCE.

WHAT TO DO IF YOU SMELL GAS:

• 

Do not try to light any appliance. 

• 

Do not touch any electric switch; 

do not use any phone in your 

building. 

• 

Immediately call your gas 

supplier from your neighbor’s 

phone. Follow the gas suppliers 

instructions. 

• 

If you cannot reach your gas 

supplier call the fire department.

WARNING! 

IF THE INFORMATION IN THIS 
MANUAL IS NOT FOLLOWED 
EXACTLY, A FIRE OR 
EXPLOSION MAY RESULT 
CAUSING PROPERTY DAMAGE, 
PERSONAL INJURY OR LOSS 
OF LIFE.

PLEASE READ THIS MANUAL 
BEFORE INSTALLING AND 
USING APPLIANCE

INSTALLER/CONSUMER

SAFETY INFORMATION

FOR YOUR SAFETY
Installation and service must 
be performed by a qualified 
installer, service agency or the 
gas supplier.

Builder Rear Vent Direct 
Vent Zero Clearance Gas 
Fireplace Heater 
Models: 33RDVDSN,    

 

 

36RDVDSN,

 

39RDVDSN

7628 

RDVN cover

6/04

WARNING:  Improper installation, 
adjustment, alteration, service or 
maintenance can cause injury or 
property damage. Refer to this 
manual. For assistance or additional 
information, consult a qualified 
installer, service agency or the gas 
supplier.

CERTIFIED

DESIGN

CERTIFIED

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Summary of Contents for 33RDVDSN













































Reviews: