Temco 33 TDVDSN Installation And Owner'S Manual Download Page 1

Page: 1 / 40

Installation Instructions and

Homeowner’s Manual

20007890 5/08 Rev. 8

DO NOT STORE OR USE
GASOLINE OR OTHER
FLAMMABLE VAPORS AND
LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER
APPLIANCE.

WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electric switch;

do not use any phone in your

building.

•

Immediately call your gas

supplier from your neighbor’s

phone. Follow the gas suppliers

instructions.

•

If you cannot reach your gas

supplier call the ﬁre department.

WARNING!

IF THE INFORMATION IN THIS
MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR
EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE,
PERSONAL INJURY OR LOSS
OF LIFE.

PLEASE READ THIS MANUAL
BEFORE INSTALLING AND
USING APPLIANCE

INSTALLER/CONSUMER

SAFETY INFORMATION

FOR YOUR SAFETY
Installation and service must
be performed by a qualiﬁed
installer, service agency or the
gas supplier.

Builder Top Vent Direct
Vent Zero Clearance Gas
Fireplace Heater
Models: 33TDVDSN,

36TDVDSN,

39TDVDSN

7636

TDVN cover

5/04

WARNING: Improper installation,
adjustment, alteration, service or
maintenance can cause injury or
property damage. Refer to this
manual. For assistance or additional
information, consult a qualiﬁed
installer, service agency or the gas
supplier.

CERTIFIED

DESIGN

CERTIFIED

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Summary of Contents for 33 TDVDSN









































Search results

Summary of Contents for 33 TDVDSN

Reviews:

Related manuals for 33 TDVDSN

Brands by name

Popular brands

Temco 33 TDVDSN, Installation And Owner'S Manual

Search results

Summary of Contents for 33 TDVDSN

Reviews:

Related manuals for 33 TDVDSN

Brands by name

Popular brands