Teltronics SEB NET-PATH Installation And Operation Manual Download | Manualshive

Page: 59 / 82

background image

Page 4-1

4

Indicators and Diagnostics

Front Panel
Indicators

The NET-PATH front panel contains a Liquid Crystal Display (LCD), four navigation
buttons (marked with arrows indicating Up, Right, Left, and Down), and four Light
Emitting Diode (LED) indicators. The LCD can display four lines, up to twenty
characters each. Software or the four navigation buttons control the display. The four
LEDs indicate the power status, battery charge status, application or database status,
and alarm conditions.

Figure 4-1 NET-PATH Front Panel Indicators

Console
Connector

Use to establish a local command line communication interface with the remote
agent. Feature not available in this release.

Indicators

The four LED indicators on the NET-PATH front panel indicate the following

conditions.

LED

Description

Power

ON indicates the NET-PATH is using commercial power.

Off indicates the NET-PATH is operating on battery power.

Battery

ON indicates the battery is fully charged.

FLASHING, indicates the battery is charging.

OFF, indicates the battery is disconnected.

Status

FLASHING indicates the NET-PATH is loading the application and
database.

ON indicates the NET-PATH has a valid database loaded.

OFF indicates the NET-PATH does not have a valid application or
database loaded.

Alarm

ON indicates that an alarm condition exists.

OFF indicates normal operation

«
...
57
58
59
60
61
...
»

Summary of Contents for SEB NET-PATH



















































































Reviews:

No comments

Related manuals for SEB NET-PATH

WJSX150 - SWITCHER - ADDENDUM

Brand: Panasonic Pages: 48

Brand: AbleNet Pages: 2

Brand: Idem Pages: 2

Brand: Contemporary Controls Pages: 4

InSwitch ISM-P Series

Brand: InHand Pages: 81

Brand: Hailink Pages: 6

Brand: Bryston Pages: 8

Brand: N-Tron Pages: 152

Brand: Cabletron Systems Pages: 83

Brand: Encore Pages: 1

Brand: StarTech.com Pages: 2

Brand: Novatek-electro Pages: 8

Brand: SyncAV Pages: 2

Brand: Zenith Pages: 22

Brand: Micronor Pages: 25

Brand: IBM Pages: 94

Brand: Mo-vis Pages: 109

Brand: B&B Electronics Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands