Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 826

Page: 826 / 1904

Page 826

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 826 of 1904

2022-03-04

Not Subject to NDA

3.9.22.

AT+CEVDP - Voice Domain Preference

This set command selects the voice domain preference.

3GPP TS 27.007

SIM Presence

Setting saved

Can be aborted

MAX timeout

SELINT

Not required

Auto

AT+CEVDP=<domain>

Parameter:

Name

Type Default

Description

<domain> string

N/A

voice domain preference.

The default value depends on product and
the support of VoLTE.

Values:

1 : CS voice only

2 : CS voice preferred, IMS PS voice as secondary

3 : IMS PS voice preferred, CS as secondary

4 : IMS PS voice only

Default value is 4 for LE910C1-SA/ST/SV/NS, and 3 for other
model.

AT+CEVDP?

Read command returns the selected domain in the format:

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands