Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 805

Page: 805 / 1904

Page 805

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 805 of 1904

2022-03-04

Not Subject to NDA

3.9.14.

AT#AUTOATT - Auto-Attach Property

Execution command has no effect and is included only for backward compatibility.

SIM Presence

Setting saved

Can be aborted

MAX timeout

SELINT

Required

Auto

AT#AUTOATT=[<auto>]

Parameter:

Name

Type

Default

Description

<auto>

integer

GPRS auto-
attach
property

Values:

0 : disables GPRS auto-attach property

1 : enables GPRS auto-attach property (factory default):

after the command #AUTOATT=1 issued (and at every
following startup) the terminal will automatically try to
attach to the GPRS service.

AT#AUTOATT?

Read command reports whether the auto-attach property is currently
enabled or not, in the format:

#AUTOATT: <auto>

AT#AUTOATT=?

Test command reports available values for parameter <auto>.

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands