manualshive.com logo in svg

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Share
Download
Page 792
Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 792

                

LE910Cx AT Commands Reference Guide

 

 

 
80502ST10950A Rev. 14 

Page 792 of 1904 

2022-03-04 

 

Not  Subject to NDA 

 

3.9.10.

 

AT+CGEQREQ - 3G Quality of Service Profile (Requested) 

The command allows to specify a 3G quality of service profile for the context identified by 
the context identification parameter. 

 

 

[1] 3GPP TS 27.007 
[2] 3GPP TS 23.107 

 

SIM Presence 

Setting saved 

Can be aborted 

MAX timeout 

SELINT 

Required 

Auto 

No 

- 

2 

 

  AT+CGEQREQ=[<cid>[,<Traffic class>[,<Maximum bitrate UL>[,<Maximum 

bitrate DL>[,<Guaranteed bitrate UL>[,<Guaranteed bitrate DL>[,<Delivery 
order>[,<Maximum SDU size>[,<SDU error ratio>[,<Residual bit error 
ratio>[,<Delivery of erroneous SDUs>[,<Transfer delay>[,<Traffic handling 
priority>[,<Source Statistics Descriptor>[,<Signalling 
Indication>]]]]]]]]]]]]]]] 

Set command specifies a 3G Quality of Service profile for the context 
identified by the (local) context identification parameter <cid> which is 
used when the MT sends an Activate PDP Context Request message to the 
network. 

Parameters: 

Name 

Type 

Default 

Description 

<cid> 

integer 

- 

PDP context identification (see 
+CGDCONT command). 

<Traffic class>  integer 

4 

traffic class 

 

Values: 

0  :  conversational 

1  :  streaming 

2  :  interactive 

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands