Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 710

Page: 710 / 1904

Page 710

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 710 of 1904

2022-03-04

Not Subject to NDA

3.7.11.

AT+CALD - Delete Alarm

This command deletes an alarm in the ME.

3GPP TS 27.007

SIM Presence

Setting saved

Can be aborted

MAX timeout

SELINT

Not required

AT+CALD=<n>

Execution command deletes an alarm in the ME.

Parameter:

Name

Type

Default

Description

<n>

integer

N/A

alarm index

Value:

0 : alarm index

AT+CALD=?

Test command reports the range of supported values for <n> parameter.

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands