Telit Wireless Solutions LE910C series At Commands Reference Manual Download Page 708

Page: 708 / 1904

Page 708

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 708 of 1904

2022-03-04

Not Subject to NDA

3.7.10.

AT+CSTF - Setting Time Format

Set command sets the time format of the time information presented to the user.

3GPP TS 27.007

SIM Presence

Setting saved

Can be aborted

MAX timeout

SELINT

Not required

Specific profile

AT+CSTF=[<mode>]

Set command sets the time format of the time information presented to
the user.

Parameter:

Name

Type

Default

Description

<mode> integer

N/A

phone display time format, The default
value is manufacturer specific.

Values:

: HH:MM (24 hour clock)

: HH:MM a.m./p.m.

3÷7 : Manufacturer specific

AT+CSTF?

Read command reports the currently selected <mode> in the format:
+CSTF: <mode>.

AT+CSTF=?

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Search results

Summary of Contents for LE910C series

Reviews:

Brands by name

Popular brands