Telguard TG-7 Series Installation & Operating Manual Download Page 33 | Manualshive

Page: 33 / 42

background image

TG-7 Cellular Series Installation & Operating Guide

27

56053501 Rev A © 2022 Telguard

Tamper Switch Installation

For all UL/ULC Commercial Burglary Installations, a tamper switch must be wired to monitor the
communicator enclosure. The wiring from the tamper switch assembly to the panel shall be in a rigid
or flexible metal conduit or be supervised along with other wiring from the communicator to the
panel. The tamper switch does not connect to the communicator circuit board.

An easy-attach tamper switch assembly is included with the TG-7 and TG-7A communicator products
and contains installation instructions. If a tamper switch is needed for a TG-7FS or TG-7UB product,
the TG-TAMPER Accessory can be purchased from most Telguard distributors. Note that a tamper
switch is required when using the TG-7FS in a combination fire and burglary system.

LED1
LED2
LED3
LED4
LED5
LED6
LED7
LED8

ALARM PANEL

TRIP

INPUT

EARTH
GROUND

NOTE 2

NOTE 2: UL/ULC BURG NOTE: Tamper
switch should be mounted on the
enclosure and connected to Alarm Panel.

AC

Plug-in

Adapter

Battery

NOTE 1

NOTE 1: Use either AC Power
(from Adapter) with Battery
or use DC Power (from Panel).

NOTE 1

TAMPER

SWITCH

A

n

te

n

n

a

«
...
31
32
33
34
35
...
»

Summary of Contents for TG-7 Series











































Reviews:

No comments

Related manuals for TG-7 Series

Univerge SV8100

Brand: NEC Pages: 4

Brand: Iget Pages: 54

Brand: O2 Pages: 72

Brand: myPhone Pages: 41

Aastra 9133i IP

Brand: ADTRAN Pages: 31

Brand: Shenzhen Pages: 57

Brand: Qubo Pages: 34

Brand: AMGOO Pages: 14

Brand: Avaya Pages: 182

Brand: BlueParrott Pages: 16

Brand: Nokia Pages: 23

Brand: Nokia Pages: 121

Brand: Nokia Pages: 131

ZENFONE 3 SERIES

Brand: Asus Pages: 35

Brand: Asus Pages: 81

Brand: Asus Pages: 80

Brand: Asus Pages: 97

Brand: Asus Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands