background image

TR-240 Users Manual - Preliminary 

Page 6 of 7 

Rev D – 3 / 09 / 2011 

 

Specifications 

 
 
Technology……………………………………… 2.4 GHz, IEEE 802.11b 
Power……………………………………………. Internal Li-Ion 7.2V, 2000mAhr, Battery.  

Typical battery life of 8 hours. 

Current Draw……………………………………. 250mA typical with radio card active 
 

 

 

 

RF Frequency Range…………………………….  802.11 Channels 1 – 11 (2.412 to 2.462GHz) 
Modulation Technology…………………………  CCK 
Antennas………………………………………… Internal dipoles 
RF Output Power (Terminated)…………… 

20mW 

Data rate.………………………………………..  5.5 Mbps (locked into) 
Sensitivity (Worst case)…………………………  5.5Mbps 10-5 BER @ -83dBm 
 

 

 

 

Frequency Response…………………………….. 400 Hz to 3900 Hz 
Dynamic Range………………………………….  66 dB 
Audio Output (headset)………………………….  70mW, 300 Ohms (1% Distortion) 
 

 

 

 

Beltpack Size……………………………………. 5.25L x 3.75W x 1.75H inches 
Beltpack Weight…………………………………  12.9 oz (w/ battery) 
FCC License……………………………………..  No License Required 
 

 

 
FCC

 

 
This device complies with Part 15 of FCC rules.  
Operation is subject to the following conditions: 
 
1.

 

This device may not cause harmful 
interference. 

 
2.

 

This device must accept any interference 
received, including interference that may 
cause undesired operation. 

 
3.

 

Use only the manufacturer or dealer supplied 
beltclip and/or accessories for this device. 

 
4.

 

This device must not be co-located or 
operated in conjunction with any other 
antenna or transmitter. 

 
 
 
The beltpack is intended to be worn on the 
belt of the user.  Placing the beltpack in other 
locations on the body may reduce 
performance and void the user’s authority by 
the FCC to operate. 
 
CAUTION: Any changes or modification not 
expressly approved by the party responsible 
for compliance could void the user’s 
authority to operate this equipment. 
 

 
 
 
 
 
 
 

Summary of Contents for TR-240








Reviews: