TELEVAC MX7M Page 6 Instruction Manual Download | Manualshive

Page: 6 / 24

background image

Instruction Manual

MX7M Active Gauge

1.6 Quick Start Guide

1.6.1 Check what you’ve received

Compare what you’ve received to your purchase order.

1.6.2 Safety Instructions

Review all safety instructions outlined in Section 2

1.6.3 Connect Power

Connect a 24V power supply to the unit. See the pin out in Figure 2 for more information.

1.6.4 Check the Measurement Screen

The unit should power up and display "OFF" on the measurement screen. Do not attempt to turn on
the high voltage.

1.6.5 Power down the MX7M

Power down the MX7M and install it on a vacuum stand for use.

2 Setup

2.1 Installation

Each MX7M is designed to be used in conjunction with a 7M sensor. The 7M sensor can be mounted
in any position however it is recommended to mount it away from any contaminants that might be
in the system as over time this can affect the measurement accuracy. Mounting the 7M sensor close
to the area where vacuum measurement is desired is preferred to increase the accuracy. Each 7M
sensor has a key that only allows for the MX7M to mate with the sensor in the proper orientation.
Rotate the MX7M until the correct alignment is obtained and the MX7M is able to slide onto the 7M
sensor. Connect the power connector to the top of the unit and be sure to tighten the screws so that
a firm connection is maintained.

Try to avoid connecting the MX7M to the vacuum chamber by long or narrow piping as this may
affect the accuracy and response time of the unit. Avoid mounting the unit near a heater within the
chamber as this may affect the measurement accuracy. Excessive vibration of the unit may affect
accuracy and decrease the life of the unit. Exposure to oils and other contaminants will decrease the
accuracy and decrease the life of the sensor. Do not expose the unit to corrosive gases.

2.2 Electrical Information

Power connectors and adapters for use with the MX7M are available for purchase from Televac. Op-
erators wishing to create their own adapters should refer to the pin out of the MX7M below. Each
connection labeled “Floating” has no connection and should remain so.

email: [email protected]

tel: +1 215 947 2500

web: frederickscompany.com

mx7m_im rev C

5 of 23

«
...
4
5
6
7
8
...
»

Summary of Contents for MX7M

























Reviews:

No comments

Related manuals for MX7M

Brand: Klarstein Pages: 36

Brand: Fraser Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands