background image

Prism TM450 Installation Guide for JBus 1708 and 1939  

Teletrac Inc. 

1634-0300 00 

Page 6 

In the Dashboard  

 

Antenna should be placed as high as possible in the dash with a clear view out the 
windshield with no metallic obstructions. 

 

Antenna must be secured in place to assure it does not move and degrade signal. 

 

Test the antenna prior to putting everything back together because some 
dashboards are made with carbon composites that will deteriorate the signal 
strength.

 

 

Testing the Installation 

Verifying that the installation is fully operational is the single most important part of the 
installation.   

Before you start the Installation Test, turn the ignition to the On position for 1 minute, 
and then turn it back to Off. 

Step 1:  

Once all power and antenna connections are complete, make sure the  

 

 

Transceiver is working properly.  The easiest way to do this is using an MDT  

 

 

955.   

 

 

Press <Control 1> to Display Radio Status, Confirm Registration and RSSI 
(>105) 

 

Confirm that the IP number displayed matches the paperwork

.   

 
Step 2

:   

Press <Control 2> in the MDT to confirm that: 

 

The number of satellites acquired is greater than 5, and  

 

The SNR is greater than 33.   

 

Confirm that date and time are valid (the time reflected will be GMT -5 to 
-8 hours of your local time). 

 
Step 3:  

MUST

 

be completed for an installation to be completed! 

There are 2 possible ways to complete Step 3: 

Option 1

- Use the eClient software - Log into the customer’s account in 

eClient on your laptop or another computer, and confirm that the IP you are 
working with is in the customer’s account and is assigned to a vehicle.   

Once you have done this, perform a locate on the vehicle to confirm that the 
vehicle responds.  

Summary of Contents for Prism TM450













Reviews: