manualshive.com logo in svg

Telegesis ETRX2USB, Command Manual, Page: 26 / 101

Share
Download
Telegesis ETRX2USB Command Manual Download Page 26

 

 

R305 AT Commands

 

 

©2011 Telegesis (UK) Ltd 

- 26 - 

 AT Command Manual (Rev 3.05) 

+POWERDESC 

–  Request Node’s Power Descriptor                                                        (ZDO) 

Execute Command 

AT+POWERDESC:<Address>,<NodeID> 

 
Where  <Address>  is  the  EUI64,  NodeID  or 
Address  table  entry  of  the  node  which  is  to 
be  interrogated  about  the  node  with  the 
NodeID specified in <NodeID>.  
 
Sends  a  unicast  to  obtain  the  specified 
device‟s power descriptor. 
 
 
 
 
 
 
 
 
 
 
 

Use on

 

All Devices  

Response 

SEQ:XX 
OK  
 

or

 ERROR:<errorcode> 

 
<errorcode> represents the error code explained in 
section 3. 

Prompt 

PowerDesc:<NodeID>,<errorcode> 
[,<PowerDescriptor>] 

 
In case of an error an errorcode other than 00 will 
be  displayed  and  the  prompt  will  end  after  the 
errorcode 
<NodeID>  is  the  Remote  node‟s  NodeID.  In 
addition  the  power  descriptor  is  displayed  as  a  16 
bit  hexadecimal  number  as  described  in  section 
2.3.2.4. of the ZigBee specification. 
 
As  with  all  unicasts  after  successful  transmission 
the sequence number of the unicast is stated using 
the  “SEQ:XX”  prompt.  When  acknowledged  (or 
not)  the 

accompanying  “ACK:XX”  (or  “NACK:XX”) 

prompt is displayed.

 

SW release

  

R302   

 

 

 

 

       

● 

 

+ACTEPDESC 

–  Request Node’s Active Endpoint List                                                      (ZDO) 

Execute Command 

AT+ACTEPDESC:<Address>,<NodeID> 

 
Where  <Address>  is  the  EUI64,  NodeID  or 
Address  table  entry  of  the  node  which  is  to 
be  interrogated  about  the  node  with  the 
NodeID specified in <NodeID>.  
 
Sends  a  unicast  to  obtain  the  specified 
device‟s active endpoint list. 
 
 
 
 
 
 
 
 
 
 

Use on

 

All Devices  

Response 

SEQ:XX 
OK  
 

or

 ERROR:<errorcode> 

 

<errorcode> represents the error code explained in 
section 3. 

Prompt 

ActEpDesc:<NodeID>,<errorcode>

[,XX,…] 

 
In case of an error an errorcode other than 00 will 
be  displayed  and  the  prompt  will  end  after  the 
errorcode

 

<NodeID>  is  the  Remote  node‟s  NodeID.  In 
addition  all  active  endpoints  are  listed  as  8-bit 
hexadecimal numbers separated by commas. 
 
As  with  all  unicasts  after  successful  transmission 
the sequence number of the unicast is stated using 
the  “SEQ:XX”  prompt.  When  acknowledged  (or 
not)  the  accompanying  “ACK:XX”  (or  “NACK:XX”) 
prompt is displayed. 

SW release

  

R302   

 

 

 

 

       

● 

Summary of Contents for ETRX2USB






































































































Reviews:

No comments