manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 99 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 99

Teledyne ML – T101 Operation Manual 

Operating Instructions 

 

95 

4.6.3.6.

 

AIN Calibration 

This is the sub-menu to conduct the analog input calibration. This calibration should only 
be necessary after major repair such as a replacement of CPU, motherboard or power 
supplies. Activate the ANALOG  I/O CONFIGURATION MENU  (see  Section  4.6.3), 
then press: 

 

 
 

 

 
 

Exit at any time to 

return to the main

 

DIAG

 menu 

 

 

 

DIAG 

 

ANALOG I / O CONFIGURATION  

 

PREV

 

NEXT

 

      

          ENTR 

 

 

EXIT

 

Continue pressing 

SET>

 until … 

 

 

 

DIAG AIO 

AIN CALIBRATED: 

NO  

 
   < SET

  

SET>

    CAL 

 

 

 

 

EXIT

 

 

 

 

DIAG AIO 

AIN CALIBRATED:

 YES

  

 
   < SET

  

SET>    CAL

 

 

 

 

 

EXIT 

Instrument 

calibrates 

automatically 

Exit to return to the 

ANALOG  I/O 

CONFIGURATION 

MENU 

STARTING FROM ANALOG I / O CONFIGURATION MENU 

 

 

 

DIAG AIO 

CALIBRATING A/D ZERO  

 

 

 
CALIBRATING A/D SPAN 

   

 

 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments