manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 145 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 145

Teledyne ML – T101 Operation Manual 

Operating Instructions 

 

141 

4.8.2.11.

 

HOLDOFF Feature 

The  DAS  HOLDOFF feature allows to prevent data collection during calibrations and 
during the DAS_HOLDOFF period enabled and specified in the VARS (Section 4.8). To 
enable or disable the HOLDOFF, follow the instruction shown in Section 4.11.2.2 then 
press

: 

 

 

 

 

 
 

Edit Data Channel Menu 

From the 

DATA ACQUISITION

 menu 

 

 

 

SETUP X.X     

  

0)

 

CONC:     ATIMER,     2,      4032, R

 

 
 PREV  NEXT            INS    DEL

   EDIT    

 PRNT 

 

  EXIT

 

Exits to the main 

Data Acquisition 

menu 

 

 

 

SETUP X.X      

NAME:CONC

 

 
    <SET  

  SET> 

 EDIT

 

   PRINT 

 

EXIT

 

 

 

 

SETUP X.X          

CAL HOLD OFF:ON

 

 
              SET>

  EDIT 

   PRINT  

EXIT

 

ENTR

 accepts the new 

setting and returns to the 

previous menu. 

EXIT

 ignores the new setting 

and returns to the previous 

menu. 

SETUP X.X        

CAL HOLD OFF:ON 

  

ON   

    

 

 

 

    ENTR    EXIT

 

 
 
 

Toggle to turn HOLDOFF 

ON or OFF 

Press 

SET> 

 until… 

 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments