manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 144 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 144

Operating Instructions 

Teledyne  ML  – T101 Operation Manual 

140 

  

4.8.2.10.

 

Disabling/Enabling  Data Channels 

Data channels can be temporarily disabled, which can reduce the read/write wear on the 
disk-on-module.  The ALL_01 channel of the T101, for example, is disabled  by default.  

To disable a data channel, follow the instruction  shown in  Section 4.11.2.2 then press: 

 

 

 

 

 
 

Edit Data Channel Menu 

From the 

DATA ACQUISITION

 menu 

 

 

 

SETUP X.X     

  

0)

 

CONC:     ATIMER,     2,       4032, R

 

 
 PREV  NEXT            INS    DEL

   EDIT    

 PRNT 

 

  EXIT

 

Exits to the main 

Data Acquisition 

menu 

 

 

 

SETUP X.X      

NAME:CONC

 

 
    <SET  

  SET> 

 EDIT

 

   PRINT 

 

EXIT

 

 

 

 

SETUP X.X      

CHANNEL ENABLE:ON

 

 
    <SET    SET>

  EDIT 

   PRINT 

 

EXIT

 

ENTR

 accepts the new 

setting and returns to the 

previous menu. 

EXIT

 ignores the new setting 

and returns to the previous 

menu. 

SETUP X.X        

CHANNEL ENABLE:ON

 

  

 OFF   

    

 

 

 

    ENTR    EXIT

 

 
 
 

Toggle to turn 

channel ON or OFF 

Press 

SET> 

 until… 

 

 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments