manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 122 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 122

Operating Instructions 

Teledyne  ML  – T101 Operation Manual 

118 

  

 

Analyzer 

Analyzer 

Analyzer 

Last Analyzer 

Female DB9 

Male DB9 

RS-232 

COM2 

RS-232 

COM2 

RS-232 

COM2 

RS-232 

COM2 

 Host 
 

RS-232 port 

Ensure jumper is 

installed between  

JP2 pins 21 

↔

 22  

in last instrument 

of multidrop chain. 

 

Figure 4-10.Multidrop PCA Host/Analyzer Interconnect Diagram 

 

7.

 

BEFORE  communicating  from  the host, power on  the instruments  and 

check that the Instrument  ID code is unique  for  each (see Section 4.7.1).  
a.  In  the SETUP Mode menu  go to SETUP>MORE>COMM>ID.  The default 

ID is typically the model  number  or “0”. 

b.  To change the identification number,  press the button below the digit 

to be changed. 

c.  Press/select ENTER  to accept the new ID  for that instrument. 

8.

 

Next, in the SETUP>MORE>COMM>COM1  menu  (do not use the COM2 

menu  for  multidrop),  edit the COM1  MODE  parameter  as follows: 

press/select EDIT and set only QUIET MODE, COMPUTER MODE, and 

MULTIDROP  MODE  to ON. Do not change any other settings. 

9.

 

Press/select ENTER  to accept the changed settings, and ensure  that COM1 

MODE  now shows 35. 

10.

 

Press/select SET>  to go  to the COM1  BAUD  RATE menu and ensure it 

reads the same for all instruments (edit as needed so that all instruments 

are set at the same  baud  rate). 

Note 

Teledyne ML recommends setting up the first link between the Host and the first analyzer and testing it 

before setting up the rest of the chain. 

The (communication) Host  instrument  can address only one instrument at a time, each by its unique ID 

(see step  7 above). 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments